DRIVE BELT INSTALLATION


  1. INSTALL V-RIBBED BELT


    1. A01H0Q6E01

      Install the V-ribbed belt as shown in the illustration.

      Note

      Check that the V-ribbed belt is properly set to each pulley.


      1. Rotate the tensioner pulley counterclockwise, and then remove the bar.

    2. A01H0W4E01

      After installing the belt, check that it fits properly in the ribbed grooves.

    3. Check by hand to confirm that the belt has not slipped out of the grooves on the bottom of the pulley.

    4. A01GZ5XE01

      Check that the alignment mark on the belt tensioner is within area "A".

      If it is outside area "A", replace the V-ribbed belt.

      Tech Tips

      When a new belt is installed, the alignment mark should be within area "B". If not, the V-ribbed belt is not installed correctly.

  2. INSTALL INTAKE AIR CONNECTOR PIPE

    A01H134E01

    1. Align the protrusion of the intake air resonator with the cutout of the bracket and insert the protrusion.

    2. Install the intake air connector pipe with the 3 hose clamps.

      Torque:
      for intake air connector pipe and throttle body
      4.8 N*m  { 49 kgf*cm, 42 in.*lbf }
      for intake air connector pipe and intake air resonator
      3.8 N*m  { 39 kgf*cm, 34 in.*lbf }

      Note

      Insert the protrusion of the intake air connector pipe into the hole of the hose clamp.

      Tech Tips


      • The intake air connector pipe and throttle body clamp can be tightened within the range of 4.0 N*m (41 kgf*cm, 35 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf), and the intake air connector pipe and intake air resonator clamp can be tightened within the range of 2.0 N*m (20 kgf*cm, 18 in.*lbf) to 5.5 N*m (56 kgf*cm, 49 in.*lbf).

      • When tightening the hose clamp, make sure the hose clamp's end is within the painted white line (width: 2 mm (0.0787 in.)).

    3. Attach the 2 wire harness clamps.

    4. A01GZROE01

      Connect the No. 1 ventilation hose and No. 2 ventilation hose to the intake air connector pipe.

      Tech Tips


      • Position the claws of the clamps as shown in the illustration.

      • Install the clamps so that they are within the hose's paint marks.

  3. INSTALL NO. 1 AIR CLEANER INLET


    1. A01GYPCE01

      Align the holes with the connection areas labeled A, and attach the No. 1 air cleaner inlet.

    2. Install the No. 1 air cleaner inlet with the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY


    1. A01GWDEE01

      Attach the 4 clips labeled B.

      Note


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.

    2. Install the air cleaner inlet cover sub-assembly with the 5 clips labeled A.

  5. INSTALL V-BANK COVER SUB-ASSEMBLY


    1. A01GZ6XE01

      After sliding the V-bank cover sub-assembly from the vehicle front to the rear to attach the 2 clips labeled A, attach the 4 clips labeled B and install the V-bank cover sub-assembly.

      CAUTION:


      • Make sure the clips are attached securely.

      • Attaching the clips forcefully or hitting the top of the clips may damage them.