FRONT WIPER MOTOR REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE UPPER RADIATOR SUPPORT SEAL


    1. Remove the 13 clips and upper radiator support seal.

  3. REMOVE FRONT FENDER SIDE PANEL PROTECTOR LH


    1. A01DT1Z

      Detach the 3 clips and guide, and remove the front fender side panel protector.

  4. REMOVE FRONT FENDER SIDE PANEL PROTECTOR RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


    1. A01DN41

      Detach the 5 claws and remove the front fender to cowl side seal LH.

  6. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

    Tech Tips

    Use the same procedure for the RH side and LH side.

  7. REMOVE WINDSHIELD WIPER ARM COVER


    1. A01DN34E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the wiper arm cover.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure for the RH and LH sides.

  8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A01DM27

      Remove the nut and front wiper arm and blade assembly LH.

  9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A01DRPL

      Remove the nut and front wiper arm and blade assembly RH.

  10. REMOVE HOOD TO COWL TOP SEAL


    1. A01DQI1

      Detach the 7 claws and 2 clips and remove the hood to cowl top seal.

  11. REMOVE CENTER NO. 2 COWL TOP VENTILATOR LOUVER


    1. A01DM7E

      Detach the 2 claws and 3 guides and remove the center No. 2 cowl top ventilator louver.

  12. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. A01DRC9E01
      Text in Illustration
      *1 Guide A
      *2 Guide B

      Remove the 2 clips.

    2. Detach the 6 claws and guide (A).

    3. Disengage the 10 guides (B) and pull out the cowl top ventilator louver sub-assembly.

  13. REMOVE WINDSHIELD WIPER MOTOR AND LINK


    1. A01DQ74

      Detach the clamp and disconnect the connector.

    2. A01DTIZ

      Remove the 2 bolts.

    3. A01DMOHE01
      Text in Illustration
      *1 Grommet

      Detach the grommet and remove the windshield wiper motor and link as shown in the illustration.

      Note

      Be careful not to damage the windshield when removing the windshield wiper motor and link assembly.

  14. REMOVE FRONT WIPER CRANK SUB-ASSEMBLY (for RHD, w/ Spring)


    1. A01DS0RE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, separate the windshield wiper link rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01DS3S

      Remove the nut and front wiper crank sub-assembly.

  15. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY


    1. w/o Spring:


      1. A01DSE3E01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, separate the windshield wiper link rod from the crank arm pivot of the front wiper crank as shown in the illustration.

        Tech Tips

        Tape the screwdriver tip before use.

    2. A01DQRA

      Disconnect the connector.

    3. Using a T30 ''TORX'' socket, remove the 2 bolts and windshield wiper motor.

  16. REMOVE WIPER MOTOR WIRE


    1. A01DO96

      Detach the claw and remove the wiper motor wire.