POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. Apply MP grease to the sliding and rotating areas of the regulator motor.

    2. Using a T25 "TORX" socket wrench, install the power window regulator motor with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.

  2. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY LH


    1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

    2. Install the temporary bolt to the rear door window regulator assembly.

    3. A01DOXCE02
      Text in Illustration
      *1 Temporary Bolt

      Temporarily install the rear door window regulator assembly with the temporary bolt.

    4. Temporarily install the 3 bolts, and then tighten the temporary bolt and 3 bolts.

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.

    2. A01DMHU

      Connect the power window regulator switch assembly and move the arm of the regulator so that the roller on the arm can be seen through the service hole.

    3. Disconnect the power window regulator switch assembly and rear power window regulator motor connector.

    4. Disconnect the cable from the negative (-) battery terminal.

      Note


      • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. A01DT6T

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrow in the illustration.

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A01DSEI

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door window division bar sub-assembly to the glass run.

    3. Install the temporary bolt to the rear door window division bar sub-assembly.

    4. Install the rear door window division bar sub-assembly.

    5. Install the 2 bolts and screw.

    6. Tighten the temporary bolt to install the rear door window division bar sub-assembly.

  6. INSTALL REAR DOOR GLASS RUN LH


    1. Install the glass run.

  7. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. A01DRBGE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.

    3. Attach the rear door service hole cover using to the reference points on the rear door panel.

      Note


      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the seal quality.

    4. Connect the connector.

    5. Attach the 2 clamps to the rear door wire.

  8. INSTALL REAR SPEAKER SET


    1. A01DUOKE01

      Temporarily install the speaker by attaching the 2 claws of the speaker to the door panel.

    2. Install the rear speaker set with the 3 screws in the order shown in the illustration.

      Note

      Do not touch the cone of the speaker.

    3. Connect the connector.

  9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH


    1. A01DMDO

      Attach the 3 claws to install the rear door inner glass weatherstrip as shown in the illustration.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01DRR0

      Install the clamp to the door panel.

    2. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. Connect each connector.

    4. A01DLYZ

      Attach the rear door trim board sub-assembly by attaching the 4 claws of the rear door inner glass weatherstrip as shown in the illustration.

    5. Attach the 9 clips and install the rear door trim board sub-assembly.

    6. Install the 3 screws.

  11. INSTALL ASSIST GRIP COVER LH


    1. A01DQ1J

      Attach the 8 claws to install the assist grip cover.

  12. INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH


    1. A01DQBR

      Attach the 3 claws to install the door inside handle bezel.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. INITIALIZE POWER WINDOW CONTROL SYSTEM


    1. Initialize the power window control system Click here.