ROOF HEADLINING (for 3 Door) REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. for LH Side:

      Remove the rear No. 1 seat assembly Click here.

    2. for RH Side:

      Remove the rear No. 1 seat assembly Click here.

  4. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    A01DNTTE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. REMOVE COWL SIDE TRIM BOARD LH

    A01DQEI

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  7. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A01DMY1

    1. Remove the front door opening trim weatherstrip.

  9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

    A01DQRKE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front No. 1 assist grip plug.


    1. Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  11. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE NO. 1 ASSIST GRIP

    A01DRDX

    Tech Tips

    Use the same procedure for the other No. 1 assist grip.


    1. Remove the 2 bolts.

    2. Detach the 2 claws and remove the No. 1 assist grip.

  13. REMOVE FRONT PILLAR GARNISH LH

    A01DS8Q

    1. Detach the 3 guides and remove the front pillar garnish.

    2. A01DQUVE01
      Text in Illustration
      *1 Curtain Shield Airbag Assembly
      *2 Adhesive Tape
      *3 Protective Cover

      w/ Curtain Shield Airbag:

      Protect the curtain shield airbag assembly.


      1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  14. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  16. REMOVE MAT SET PLATE COVER

    A01DNTXE01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for all mat set plate covers.


    1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

      Tech Tips

      Tape the screwdriver tip before use.

  17. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    A01DSF1

    1. Remove the 5 screws.

    2. Detach the 6 claws and remove the rear floor mat rear support plate.

  18. REMOVE QUARTER TRIM COVER HOLE LH

    A01DOG6

    1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.

  19. REMOVE QUARTER TRIM COVER HOLE RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE REAR FLOOR CARPET ASSEMBLY

    A01DTIS

    1. Remove the rear floor carpet.

  21. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    A01DNOJ

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Remove the luggage compartment trim hook by turning it clockwise.

  22. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    A01DMF1E01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for the other tonneau cover holder cap.


    1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    A01DTB0E01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  24. REMOVE QUARTER TRIM POCKET TRAY

    A01DRRVE01
    Text in Illustration
    *1 Protective tape

    1. Put protective tape around the quarter trim pocket tray.

    2. Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.

      Tech Tips

      Tape the screwdriver tip before use.

  25. REMOVE OUTER LAP BELT ANCHOR COVER

    A01DRK4

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Detach the 3 claws and remove the outer lap belt anchor cover.

  26. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    A01DO0R

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A01DOAG

      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    3. Remove the 3 bolts and 2 screws.

    4. Detach the 9 claws and 12 clips and remove the deck trim side panel.

      A01DR76

  27. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

    A01DRMK

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A01DRY9

      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    3. Remove the 3 bolts and 2 screws.

    4. Detach the 9 claws and 12 clips.

    5. Disconnect the connector and remove the deck trim side panel.

      A01DSMT

  28. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

    A01DO0J

    1. Move the front shoulder belt anchor adjuster to the lowest position.

    2. Remove the bolt.

    3. Detach the 2 clips and 2 guides.

    4. Pass the front seat outer belt floor anchor through the front quarter trim panel and remove the front quarter trim panel.

  29. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH

    A01DPPE

    1. Detach the 7 clips.

    2. A01DOBV

      Detach the 4 claws and 2 guides, pass the rear No. 1 seat belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.

  31. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A01DNR9E03
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  33. REMOVE REAR ASSIST GRIP ASSEMBLY LH

    A01DRRAE03
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip.

    3. Remove the 2 clips from the vehicle body.

  34. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  35. REMOVE VISOR BRACKET COVER LH

    A01DRDT

    Tech Tips

    Use the same procedure for the other visor bracket cover.


    1. Detach the 4 claws and remove the visor bracket cover.

  36. REMOVE VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. REMOVE VISOR ASSEMBLY LH

    A01DNDQ

    1. Remove the 2 screws and visor.

  38. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE VISOR HOLDER

    A01DS2GE02

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

  40. REMOVE MAP LIGHT ASSEMBLY


    1. A01DOJ7

      Detach the 4 clips.

    2. Disconnect the connector and remove the map light.

  41. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A01DO74

      Detach the 2 claws and remove the rain sensor cover.

  42. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A01DOYR

      Detach the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.

    2. A01DLV7

      Detach the 2 claws and remove the inner rear view mirror stay holder cover.

  43. REMOVE NO. 1 ROOM LIGHT ASSEMBLY


    1. Remove the No. 1 room light assembly Click here.

  44. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. Remove the No. 2 room light assembly Click here.

  45. REMOVE NO. 1 ROOF SIDE RAIL GARNISH LH

    A01DNVFE01
    Text in Illustration
    *a Cut Off Position

    1. Detach the 5 clips.

    2. Cut off the 5 clips and remove the roof side rail garnish LH.

    3. Remove the 5 clips from the vehicle body.

  46. REMOVE NO. 1 ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  47. REMOVE ROOF HEADLINING ASSEMBLY

    A01DPHK

    1. w/ EC Mirror:

      Disconnect the inner mirror connector.

    2. A01DMZQ

      w/ Rain Sensor:

      Disconnect the rain sensor connector.

    3. A01DRYK

      w/ Sliding Roof:

      Disconnect the drive gear connector.

    4. A01DP8G

      w/ Digital Audio Broadcasting Antenna:

      Disconnect the connector and detach the wire harness clamp.

    5. A01DP1R

      Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.

    6. A01DM4R

      Remove the bolt.

    7. Disconnect the 2 connectors and detach the 3 clamps from the front pillar RH.

    8. A01DPM9

      Disconnect the connector and detach the 3 clamps from the rear pillar LH.

    9. A01DSAM

      Disconnect the connector and detach the 4 clamps from the rear pillar RH.

    10. A01DN4X

      w/o Sliding Roof:


      1. Detach the 2 clips.

    11. A01DMATE01
      Text in Illustration
      *1 Guide
      *2 Fastener

      w/ Sliding Roof:


      1. Detach the 2 clips, 2 guides and 8 fasteners.

    12. A01DSY9

      Remove the roof headlining from the back door as shown in the illustration.

      Note

      Be careful not to damage the roof headlining when removing it.

  48. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

    A01DUWB

    1. Detach the 4 claws of the front shoulder belt anchor plate and slide the front shoulder belt anchor plate in the direction of the arrow to remove it.

  49. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  50. REMOVE REAR NO. 2 SIDE RAIL SPACER LH

    A01DUTM

    1. Remove the clip.

    2. Detach the 4 claws and remove the rear side rail spacer.

  51. REMOVE REAR NO. 2 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  52. REMOVE DECK SIDE TRIM CUP HOLDER LH

    A01DQWW

    1. Detach the 4 claws and remove the deck side trim cup holder.

  53. REMOVE DECK SIDE TRIM CUP HOLDER RH

    Tech Tips

    Use the same procedure described for the LH side.

  54. REMOVE REAR SEAT SHOULDER BELT HANGER LH

    A01DUT7

    1. Detach the claw and guide and remove the rear seat shoulder belt hanger.

  55. REMOVE REAR SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedure described for the LH side.

  56. REMOVE QUARTER TRIM COVER

    A01DT67

    Tech Tips

    Use the same procedure for the other quarter trim cover.


    1. Detach the 2 claws and remove the quarter trim cover.

  57. REMOVE QUARTER TRIM JACK COVER (w/ Spare Tire)

    A01DQ67

    1. Detach the 7 claws and 3 guides and remove the quarter trim jack cover.

  58. REMOVE DECK SIDE TRIM COVER RH (w/o Spare Tire)

    A01DSOY

    1. Turn the 2 knobs and release the lock.

    2. Detach the 7 claws and 3 guides and remove the deck side trim cover.