ROOF HEADLINING (for 5 Door) INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR NO. 3 SIDE RAIL SPACER LH


    1. Attach the 2 claws to install the rear No. 3 side rail spacer.

  2. INSTALL REAR NO. 3 SIDE RAIL SPACER RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. Attach the 2 claws to install the rear No. 2 side rail spacer.

  4. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. Attach the 2 claws to install the rear side rail spacer.

  6. INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL DECK SIDE TRIM COVER LH


    1. Attach the 3 claws and 2 guides to install the deck side trim cover.

  8. INSTALL QUARTER TRIM JACK COVER


    1. Attach the 3 claws and 2 guides to install the quarter trim jack cover.

  9. INSTALL QUARTER TRIM COVER

    Tech Tips

    Use the same procedure for the other quarter trim cover.


    1. Attach the 2 claws to install the quarter trim cover.

  10. INSTALL REAR SEAT SHOULDER BELT HANGER LH


    1. Attach the claw and guide to install the rear seat shoulder belt hanger.

  11. INSTALL REAR SEAT SHOULDER BELT HANGER RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. INSTALL ROOF SIDE INNER GARNISH CAP LH (w/o Rear No. 2 Seat)


    1. Attach the 4 claws and 2 guides to install the roof side inner garnish cap.

  13. INSTALL ROOF SIDE INNER GARNISH CAP RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  14. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Attach the 6 claws to install the rear belt anchor plate.

  15. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH


    1. Attach the 5 claws to install the front belt anchor plate.

  17. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. INSTALL ROOF HEADLINING ASSEMBLY


    1. Place the roof headlining into the vehicle through the back door.

      Note

      Be careful not to damage the roof headlining when placing it in the cabin.

    2. A01DSL5

      w/o Sliding Roof:


      1. Attach the 2 clips to install the roof headlining.

    3. A01DTTSE01
      Text in Illustration
      *1 Guide
      *2 Fastener

      w/ Sliding Roof:


      1. Attach the 2 clips, 2 guides and 8 fasteners to install the roof headlining.

    4. A01DQVPE01
      Text in Illustration
      *1 Guide
      *2 Fastener

      w/ Rear Seat Entertainment System:


      1. Attach the 2 clips, 2 guides and 6 fasteners to install the roof headlining.

    5. w/ Rear Seat Entertainment System:

      Connect the 2 connectors.

    6. Connect the connector and attach the 3 clamps to the rear pillar RH.

    7. Connect the 2 connectors and attach the clamp to the rear pillar LH.

    8. Connect the 2 connectors and attach the 3 clamps to the front pillar RH.

    9. Install the bolt.

    10. Connect the 2 connectors and attach the 3 clamps to the front pillar LH.

    11. w/ Digital Audio Broadcasting Antenna:

      Connect the connector and attach the wire harness clamp.

    12. w/ Sliding Roof

      Connect the drive gear connector.

    13. w/ Rain Sensor:

      Connect the rain sensor connector.

    14. w/ EC Mirror:

      Connect the inner mirror connector.

  19. INSTALL REAR HEADER SPEAKER ASSEMBLY (w/ Rear Air Conditioning System)


    1. Install the rear header speaker assembly with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Connect the connector.

  20. INSTALL REAR SIDE NO. 1 AIR DUCT (w/ Rear Air Conditioning System)


    1. Insert the upper part of the duct into the roof side duct and, using that point as a pivot point, swing the duct into place and install it to the rear cooling unit.

    2. Attach the 2 claws to install the cooler plate.

  21. INSTALL NO. 1 ROOF SIDE RAIL GARNISH LH

    A01DOUKE01
    Text in Illustration
    *1 New Clip

    1. Install 3 new clips to the No. 1 roof side rail garnish LH.

    2. Attach the 3 clips to install the No. 1 roof side rail garnish LH.

  22. INSTALL NO. 1 ROOF SIDE RAIL GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. Attach the 7 claws and 4 clips to install the television base.

  24. INSTALL NO. 2 ROOM LIGHT ASSEMBLY


    1. Install the No. 1 room light assembly Click here.

  25. INSTALL NO. 1 ROOM LIGHT ASSEMBLY


    1. Install the No. 2 room light assembly Click here.

  26. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A01DLV7

      Attach the 2 claws.

    2. A01DU1OE01

      Attach the 2 claws as shown in the illustration to install the inner rear view mirror stay holder cover.

  27. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)


    1. Attach the 2 claws to install the rain sensor cover.

  28. INSTALL MAP LIGHT ASSEMBLY


    1. Connect the connector.

    2. Attach the 4 clips to install the map light.

  29. INSTALL VISOR HOLDER

    Tech Tips

    Use the same procedure for the other visor holder.


    1. Attach the 2 claws.

    2. Push in the visor holder to install it.

  30. INSTALL VISOR ASSEMBLY LH


    1. Install the visor with the 2 screws.

  31. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  32. INSTALL VISOR BRACKET COVER LH

    Tech Tips

    Use the same procedure for the other visor bracket cover.


    1. Attach the 4 claws to install the visor bracket cover.

  33. INSTALL VISOR BRACKET COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  34. INSTALL ASSIST GRIP (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Install the assist grip with the 2 bolts.

    2. Attach the 4 claws to close the 2 covers.

  35. INSTALL REAR ASSIST GRIP ASSEMBLY LH

    A01DQWU

    1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip.

  36. INSTALL REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  37. INSTALL ASSIST GRIP SUB-ASSEMBLY

    A01DN40

    1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip.

  38. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY LH


    1. w/ Rear No. 2 Seat:


      1. Attach the 4 clips and 2 guides and pass the rear No. 2 seat outer belt floor anchor through the rear quarter trim panel.

    2. Attach the 7 clips and 2 guides to install the rear quarter trim panel.

  39. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  40. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH


    1. Pass the rear No. 1 seat outer belt floor anchor through the front quarter trim panel.

    2. Attach the 2 clips and 2 guides to install the front quarter trim panel.

  41. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. w/o Rear No. 2 Seat:


      1. Pass the rear seatback lock control lever base through the deck trim side panel.

      2. Attach the 5 clips and 8 claws to install the deck trim side panel.

      3. Install the 4 bolts and 2 screws.

      4. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.

      5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. w/ Rear No. 2 Seat:


      1. Attach the 4 clips and 8 claws to install the deck trim side panel.

      2. Install the 2 bolts and 2 screws.

      3. Install the rear No. 2 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  43. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. w/o Rear No. 2 Seat:


      1. Connect each connector.

      2. Pass the rear seatback lock control lever base through the deck trim side panel.

      3. Attach the 5 clips and 8 claws to install the deck trim side panel.

      4. Install the 4 bolts and screw.

      5. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.

      6. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. w/ Rear No. 2 Seat:


      1. Connect each connector.

      2. Attach the 4 clips and 8 claws to install the deck trim side panel.

      3. Install the 2 bolts and screw.

      4. Install the rear No. 2 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

        Torque:
        42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  44. INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Install the assist grip with the 2 bolts.

  45. INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for all assist grip plugs.


    1. Attach the 2 claws to install the assist grip plug.

  46. INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Attach the 2 claws to install the front deck side trim cover

  47. INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    Tech Tips

    Use the same procedure for the other No. 1 tonneau cover holder cap.


    1. Attach the 2 claws to install the No. 1 tonneau cover holder cap.

  48. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Install the No. 1 luggage compartment trim hook by turning it clockwise.

  49. INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    Tech Tips

    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


    1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

  50. INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)


    1. Attach the 4 claws to install the rear floor carpet.

      A01DNAME01
      Text in Illustration
      *A w/o Deck Rail *B w/ Deck Rail
      *C for Face to Face Seat Type - -

  51. INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)


    1. Install the floor side rail with the 3 bolts.

  52. INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  53. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)


    1. Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.

  54. INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)


    1. Attach the clip to install the No. 1 deck board.

  55. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

    A01DTUCE01
    Text in Illustration
    *1 Luggage Hold Belt Striker

    Tech Tips

    Use the same procedure for the other front luggage compartment trim cover.


    1. Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.

    2. Attach the 4 claws to install the cap.

  56. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover.

  57. INSTALL CENTER PILLAR GARNISH LH


    1. Pass the front seat outer belt floor anchor through the center pillar garnish.

    2. Attach the 2 clips and 2 guides to install the center pillar garnish.

    3. Install the bolt.

  58. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  59. INSTALL NO. 2 ASSIST GRIP

    Tech Tips

    Use the same procedure for the other No. 2 assist grip.


    1. Attach the 2 claws to install the No. 2 assist grip.

    2. Install the 2 bolts.

  60. INSTALL NO. 2 ASSIST GRIP PLUG LH

    Tech Tips

    Use the same procedure for the other front No. 2 assist grip plug.


    1. Attach the 2 claws to install the front No. 2 assist grip plug.

  61. INSTALL NO. 2 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  62. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. Attach the 4 claws and 2 clips to install the lower center pillar garnish.

    2. Install the front seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  63. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  64. INSTALL OUTER LAP BELT ANCHOR COVER

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Attach the 3 claws to install the outer lap belt anchor cover

  65. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A01DSXRE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the rear door opening trim weatherstrip with the mark position on the vehicle and install the rear door opening trim weatherstrip as shown in the illustration.

  66. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  67. INSTALL REAR DOOR SCUFF PLATE LH


    1. Attach the 3 clips, 6 claws and 2 guides to install the rear door scuff plate.

  68. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  69. INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)


    1. Install the quarter scuff plate with the 2 bolts.

  70. INSTALL QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure described for the LH side.

  71. INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for all rear No. 1 floor step covers.


    1. Attach the 2 claws to install the rear No. 1 floor step cover.

  72. INSTALL FRONT PILLAR GARNISH LH


    1. Attach the 3 guides to install the front pillar garnish.

  73. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  74. INSTALL NO. 1 ASSIST GRIP

    Tech Tips

    Use the same procedure for the other No. 1 assist grip.


    1. Attach the 2 claws to install the No. 1 assist grip.

    2. Install the 2 bolts.

  75. INSTALL FRONT NO. 1 ASSIST GRIP PLUG LH

    Tech Tips

    Use the same procedure for the other front No. 1 assist grip plug.


    1. Attach the 2 claws to install the front No. 1 assist grip plug.

  76. INSTALL FRONT NO. 1 ASSIST GRIP PLUG RH

    Tech Tips

    Use the same procedure described for the LH side.

  77. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A01DMZFE01
    Text in Illustration
    *1 Paint Mark
    *2 Mark Position

    1. Align the paint mark on the front door opening trim weatherstrip with the mark position on the vehicle and install the front door opening trim weatherstrip as shown in the illustration.

  78. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  79. INSTALL COWL SIDE TRIM BOARD LH


    1. Attach the clip and claw to install the cowl side trim board.

    2. Install the clip.

  80. INSTALL COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  81. INSTALL DOOR SCUFF PLATE ASSEMBLY LH


    1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate.

  82. INSTALL DOOR SCUFF PLATE ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  83. INSTALL REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Double-folding Seat Type LH Side:

      Install the rear No. 1 seatback assembly Click here.

    2. for 60/40 Split Double-folding Seat Type RH Side:

      Install the rear No. 1 seatback assembly Click here.

  84. INSTALL REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. for 60/40 Split Slide Walk-in Seat Type LH Side:

      Install the rear No. 1 seat assembly Click here.

    2. for 60/40 Split Slide Walk-in Seat Type RH Side:

      Install the rear No. 1 seat assembly Click here.

  85. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. for Manual Seat Type:

      Install the rear No. 2 seat assembly Click here.

    2. for Power Seat Type:

      Install the rear No. 2 seat assembly Click here.

    3. for Face to Face Seat Type:

      Install the rear No. 2 seat assembly Click here.

  86. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.