AIR CONDITIONING PRESSURE SENSOR INSTALLATION


  1. INSTALL AIR CONDITIONING PRESSURE SWITCH


    1. Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pressure switch.

      Compressor oil
      ND-OIL 8 or equivalent

    2. Install the O-ring to the pressure switch.

    3. A01DOVXE01
      Text in Illustration
      *a Hold
      *b Turn

      Install the pressure switch.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

    4. Connect the connector.

  2. CHARGE REFRIGERANT

    SST
    09985-20010   ( 09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070 )

    1. Perform vacuum purging using a vacuum pump.

    2. Charge refrigerant HFC-134a (R134a).

      Standard
      Model Code Air Conditioning Type Cool Box Refrigerant Charging Amount
      Except the model codes below w/o Rear Cooler w/ Cool Box 600 +/-30 g (21.2 +/-1.1 oz.)
      w/o Cool Box 550 +/-30 g (19.3 +/-1.1 oz.)
      w/ Rear Cooler w/ Cool Box 800 +/-30 g (28.2 +/-1.1 oz.)
      w/o Cool Box 770 +/-30 g (27.2 +/-1.1 oz.)

      w/ Rear Cooler

      for Cold Area Specification Vehicles

      		 w/o Cool Box 720 +/-30 g (25.3 +/-1.1 oz.)

      TRJ150L-GKMEKV

      TRJ150L-GKPEKV

      TRJ155L-GJPEKV

      GRJ150L-GKFEKV

      GRJ150L-GKAEKV

      KDJ150L-GKFEYV

      KDJ150L-GKAEYV

      		 w/o Rear Cooler w/ Cool Box 600 +/-30 g (21.2 +/-1.1 oz.)
      w/o Cool Box 550 +/-30 g (19.3 +/-1.1 oz.) or 600 +/-30 g (21.2 +/-1.1 oz.) *1
      w/ Rear Cooler w/ Cool Box 800 +/-30 g (28.2 +/-1.1 oz.)
      w/o Cool Box 770 +/-30 g (27.2 +/-1.1 oz.)

      *1: For vehicles with the 2TR-FE engine which have neither the rear cooler nor cool box, the refrigerant charging amount changes based on region.

      A01DN0ZE19

      Note


      • Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.

      • Approximately 100 g (3.53 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.

  3. WARM UP ENGINE


    1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

      Note

      Be sure to warm up the compressor when turning the A/C switch is on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.

  4. CHECK FOR REFRIGERANT GAS LEAK


    1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

      Note

      Be sure to warm up the compressor when turning the A/C switch is on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.

  5. INSTALL RADIATOR GRILLE


    1. Install the radiator grille Click here.

  6. INSTALL UPPER RADIATOR SUPPORT SEAL


    1. Install the upper radiator support seal with the 13 clips.