REAR CENTER SEAT OUTER BELT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    1. Remove the rear No. 1 seat assembly LH Click here.

  2. REMOVE REAR SEAT UPPER RECLINING COVER LH

    A01DSVIE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    A01DMH2

    1. Remove the 3 screws and reclining adjuster release handle LH.

  4. REMOVE CENTER SEAT HINGE COVER RH

    A01DLY4

    1. Using a clip remover, remove the clip.

    2. Detach the 2 guides and remove the center seat hinge cover LH.

  5. REMOVE REAR SEAT CUSHION MOULDING LH

    A01DR94

    1. Using a clip remover, detach the clip.

    2. Using a moulding remover, detach the 3 claws.

    3. Move the rear seat cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding LH.

  6. REMOVE REAR SEATBACK LOCK STRIKER COVER LH

    A01DTGV

    1. Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover LH.

  7. REMOVE SEAT CUSHION COVER WITH PAD


    1. A01DSJ3

      w/ Seat Heater System:


      1. Disconnect the 2 rear seat heater connectors.

      2. A01DR50

        Pull out the wire harness as shown in the illustration.

    2. A01DSOO

      Detach the hooks.

    3. A01DO80

      Detach the hook and remove the seat cushion cover with pad.

  8. REMOVE CENTER SEATBACK ASSEMBLY

    A01DQG0

    1. Remove the 2 bolts and center seatback assembly.

  9. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH


    1. A01DQ3N

      Remove the bolt and inner belt, and disconnect the 3 point type belt anchor.

  10. REMOVE RECLINING ADJUSTER KNOB CAP LH

    A01DRFLE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap LH.

      Tech Tips

      Tape the screwdriver tip before use.

  11. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    1. A01DPON

      Remove the 2 screws.

    2. A01DN1KE02

      Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly LH.

  12. REMOVE SEAT BELT ANCHOR COVER CAP


    1. A01DMP0E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.

      Tech Tips

      Tape the screwdriver tip before use.

  13. REMOVE REAR SEAT SHOULDER BELT COVER


    1. Disconnect the outer belt from the rear seat shoulder belt cover.

    2. A01DUWH

      Detach the 2 claws and 2 guides, and then remove the rear seat shoulder belt cover.

  14. REMOVE REAR SEATBACK COVER

    A01DSPY

    1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

      Tech Tips

      Tape the screwdriver tip before use.

  15. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH

    A01DPQ6

    1. Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly LH.

  16. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    A01DNOV

    1. Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.

  17. REMOVE SEATBACK COVER WITH PAD


    1. A01DN78E01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the 10 hog rings and detach the hooks, and then remove the seatback cover with pad.

    2. A01DUW0

      Disconnect the outer belt from the seatback cover with pad.

    3. w/ Seat Heater System:


      1. A01DS5J

        Remove the wire harness.

  18. REMOVE REAR SEAT SHOULDER BELT GUIDE

    A01DOHK

    1. Detach the claw and guide, and then remove the rear seat shoulder belt guide.

  19. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A01DSJW

    1. Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.