REAR CENTER SEAT OUTER BELT ASSEMBLY (for 60/40 Split Tumble Seat Type LH Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
Note

When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.
1. Align the seat belt positioning holes with the claws and install the retractor of the 3 point type belt with the nut as shown in the illustration.
2. Install the belt sensor with the 3 nuts.
INSTALL REAR SEAT SHOULDER BELT GUIDE
1. Attach the 4 guides to install the belt guide.
2. Connect the outer belt to the belt guide.
3. Attach the 2 claws to close the cover.
INSTALL RECLINING ADJUSTER COVER LH
1. Attach the 4 claws to install the cover.
2. Install the 4 screws.
INSTALL REAR SEAT INNER RECLINING COVER RH
1. Attach the 2 claws to install the cover.
INSTALL SEPARATE TYPE REAR SEATBACK COVER
1. Install the seatback cover with 2 new hog rings and attach the fastening tape.
2. Using hog ring pliers, install the new hog rings.
  Note
  
  Be careful not to damage the cover.
  
  When installing the hog rings, avoid wrinkling the cover.
  Text in Illustration
  
  *1 Hog Ring Pliers *2 Fastening Tape
INSTALL SEATBACK COVER WITH PAD
1. Connect the outer belt to the seatback cover with pad.
2. Attach the 2 hooks to install the seatback cover with pad.
INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
1. Attach the 8 claws to install the 4 supports.
INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
1. Connect the cable in the order shown in the illustration to install the lever.
2. Install the 2 screws.
INSTALL REAR SEATBACK LOCK STRIKER COVER
1. Attach the guide and claw to install the cover.
INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH
1. Connect the outer belt to the cover.
2. Attach the 4 claws to install the cover.
INSTALL SHOULDER BELT ANCHOR COVER
1. Attach the 2 claws and 2 guides to install the cover.
INSTALL REAR SEAT ARMREST SUPPORT
1. Install the armrest support to the armrest hinge.
INSTALL REAR CENTER SEAT ARMREST HINGE
1. Install the armrest hinge with the screw.
INSTALL REAR SEAT CENTER ARMREST ASSEMBLY
1. Install the center armrest and bush with the 2 bolts.
INSTALL REAR SEAT INNER RECLINING COVER RH
1. Attach the 2 guides and 2 claws to install the cover.
INSTALL NO. 1 SEATBACK PAD LH
1. Install the seatback pad.
2. Close the 2 fasteners, and then close the seatback cover.
3. Text in Illustration
  
  *1 Hog Ring Pliers
  
  Using hog ring pliers, install 6 new hog rings.
4. Attach the 3 fastening tapes and close the cover.
5. Text in Illustration
  
  *1 Protruding Part
  
  Connect the outer belt with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear No. 1 seat outer belt to overlap the protruding parts of the seat cushion frame.
INSTALL REAR SEATBACK COVER
1. Attach the 8 claws to install the 2 covers.
CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH
Text in Illustration

*a Protruding Part
1. Connect the belt with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear No. 1 seat outer belt to overlap the protruding parts of the seat cushion frame.
INSTALL REAR SEAT CUSHION COVER SUB-ASSEMBLY LH
Text in Illustration

*1 Hog Ring Pliers
1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
  Note
  - Be careful not to damage the cover.
  - When installing the hog rings, avoid wrinkling the cover.
INSTALL REAR SEAT INNER CUSHION EDGE PROTECTOR LH
1. Install the protector with new tack pins.
INSTALL SEAT CUSHION COVER WITH PAD
Text in Illustration

*1 Hog Ring Pliers
1. Using hog ring pliers, install the seatback cover with pad with new hog rings.
2. Install the carpet with new tack pins.
INSTALL REAR NO. 2 SEAT HINGE COVER RH
1. Attach the 3 claws to install the cover.
INSTALL REAR NO. 2 SEAT HINGE COVER LH
1. Attach the 3 claws to install the cover.
INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH
1. Temporarily install the under cover to the seat cushion frame.
INSTALL REAR SEAT CUSHION SUPPORT SPRING
1. Install the spring to the seat cushion frame
  
  Tech Tips
  
  Use the same procedure for both springs.
INSTALL REAR SEAT CUSHION EDGE PROTECTOR
1. Install the protector to the cushion frame.
  
  Tech Tips
  
  Use the same procedure for both protectors.
INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH
1. Install the hinge.
2. Install the pin to the hinge.
3. Install a new E-ring.
INSTALL REAR SEAT STAY SUB-ASSEMBLY
1. Connect the seat stay ball-joint to the seat hinge.
  
  Tech Tips
  
  It is only necessary to perform this step when replacing the seat stay and seat hinge. After the seat stay is connected to the seat hinge, it cannot be disconnected.
INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH
1. Install the spring of the seat stay ball-joint.
2. Temporarily install the seat hinge and seat stay as a unit.
3. Raise the under cover.
4. Connect the seat stay to the seat cushion frame.
5. Connect the reclining release handle to the under cover.
6. Install the 5 screws.
7. Attach the 10 claws to install the under cover.
8. Install the pin to the hinge.
9. Install a new E-ring.
INSTALL REAR SEAT HINGE PAWL GUIDE
1. Attach the 4 claws to install the pawl guide.
  
  Tech Tips
  
  Use the same procedure for both pawl guides.
INSTALL SEAT TRACK OPEN LEVER PIN SUB ASSEMBLY
1. Install the pin as shown in the illustration.
2. Install the stopper.
  
  Tech Tips
  
  Use the same procedure for both pins.
INSTALL RECLINING ADJUSTER INSIDE COVER LH
1. Attach the 2 claws to install the cover.
2. Install the 2 screws.
INSTALL REAR NO. 2 SEAT CUSHION
1. Install the cushion with the screw.
INSTALL REAR NO. 1 SEAT RECLINING COVER RH
1. Attach the 2 hooks.
2. Attach the guide and 2 claws to install the cover.
3. Install the 2 screws.
INSTALL REAR SEAT RECLINING COVER LH
1. Attach the guide and 2 claws to install the cover.
2. Install the 2 screws.
INSTALL REAR NO. 1 SEAT ASSEMBLY LH
1. Install the rear No. 1 seat assembly LH Click here.