REAR CENTER SEAT INNER BELT ASSEMBLY (for 60/40 Split Tumble Seat Type LH Side) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


  1. REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    1. Remove the rear No. 1 seat assembly LH Click here.

  2. REMOVE REAR SEAT RECLINING COVER LH

    A01DQZV

    1. Remove the 2 screws.

    2. Using a moulding remover, detach the 2 claws.

    3. Move the cover in the direction of the arrow to detach the guide and remove the cover.

  3. REMOVE REAR NO. 1 SEAT RECLINING COVER RH

    A01DNDZ

    1. Remove the 2 screws.

    2. Using a moulding remover, detach the 2 claws.

    3. Move the cover in the direction of the arrow to detach the guide.

    4. A01DU0J

      Detach the 2 hooks and remove the cover.

  4. REMOVE REAR NO. 2 SEAT CUSHION

    A01DTYY

    1. Remove the screw and cushion.

  5. REMOVE REAR RECLINING ADJUSTER INSIDE COVER LH

    A01DQA8

    1. Remove the 2 screws.

    2. Detach the 2 claws and remove the cover.

  6. REMOVE SEAT TRACK OPEN LEVER PIN SUB-ASSEMBLY

    A01DQYP

    1. Using a screwdriver, remove the stopper.

    2. Remove the pin as shown in the illustration.

      Tech Tips

      Use the same procedure for both pins.

  7. REMOVE REAR SEAT HINGE PAWL GUIDE

    A01DOMQ

    1. Detach the 4 claws and remove the pawl guide.

      Tech Tips

      Use the same procedure for both pawl guides.

  8. REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH


    1. A01DNBL

      Using a screwdriver, remove the E-ring.

    2. A01DSUL

      Remove the pin.

    3. A01DQHO

      Using a screwdriver, detach the 10 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    4. A01DNPK

      Remove the 5 screws.

    5. Disconnect the reclining release handle from the under cover.

    6. Raise the under cover.

    7. A01DQN2

      Using a screwdriver, remove the spring of the seat stay ball-joint.

    8. Disconnect the seat stay from the seat cushion frame.

    9. Remove the seat hinge and seat stay as a unit.

      Note

      The seat stay cannot be disconnected from the seat hinge. If the stay is disconnected from the hinge, replacement of both parts is necessary.

      Tech Tips

      If it is necessary to replace the seat hinge, replace it together with the seat stay as the stay cannot be disconnected from the hinge.

  9. REMOVE REAR SEAT STAY SUB-ASSEMBLY

    Tech Tips


    • As the seat stay cannot be disconnected from the seat hinge, it is removed in the previous step.

    • If it is necessary to replace the seat stay, replace it together with the seat hinge as the stay cannot be disconnected from the hinge.

  10. REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH


    1. A01DOS2

      Using a screwdriver, remove the E-ring.

    2. A01DRMG

      Remove the pin and hinge.

  11. REMOVE REAR SEAT CUSHION EDGE PROTECTOR

    A01DTE5

    1. Remove the protector from the cushion frame.

      Tech Tips

      Use the same procedure for both protectors.

  12. REMOVE FOLD SEAT LEG LOCK CUSHION

    A01DUWK

    1. Remove the cushion from the protector.

      Tech Tips

      Use the same procedure for both cushions.

  13. REMOVE REAR SEAT CUSHION SUPPORT SPRING

    A01DSLP

    1. Remove the spring from the seat cushion frame.

      Tech Tips

      Use the same procedure for both springs.

  14. REMOVE REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH


    1. Remove the under cover.

  15. REMOVE REAR NO. 2 SEAT HINGE COVER LH

    A01DOYS

    1. Detach the 3 claws and remove the cover.

  16. REMOVE REAR NO. 2 SEAT HINGE COVER RH


    1. Detach the 3 claws and remove the cover.

  17. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH


    1. A01DMUN

      Remove the bolt and disconnect the inner belt.