Click here

REAR CENTER SEAT INNER BELT ASSEMBLY (for 60/40 Split Tumble Seat Type LH Side) INSTALLATION

Click here
Click here Click here
CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Click here
  1. Click here

    INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH


    1. Connect the belt with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 1 seat outer belt to overlap the protruding parts of the seat cushion frame.

      Table 1. Text in Illustration
      *a Protruding Part
  2. Click here

    INSTALL REAR NO. 2 SEAT HINGE COVER RH


    1. Attach the 3 claws to install the cover.

  3. Click here

    INSTALL REAR NO. 2 SEAT HINGE COVER LH


    1. Attach the 3 claws to install the cover.

  4. Click here

    INSTALL REAR SEAT CUSHION UNDER COVER SUB-ASSEMBLY LH


    1. Temporarily install the under cover to the seat cushion frame.

  5. Click here

    INSTALL REAR SEAT CUSHION SUPPORT SPRING


    1. Install the spring to the seat cushion frame

      Tip:

      Use the same procedure for both springs.

  6. Click here

    INSTALL FOLD SEAT LEG LOCK CUSHION


    1. Install the cushion to the protector.

      Tip:

      Use the same procedure for both cushions.

  7. Click here

    INSTALL REAR SEAT CUSHION EDGE PROTECTOR


    1. Install the protector to the cushion frame.

      Tip:

      Use the same procedure for both protectors.

  8. Click here

    INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH


    1. Install the hinge.

    2. Install the pin to the hinge.

    3. Install a new E-ring.

  9. Click here

    INSTALL REAR SEAT STAY SUB-ASSEMBLY


    1. Connect the seat stay ball-joint to the seat hinge.

      Tip:

      It is only necessary to perform this step when replacing the seat stay and seat hinge. After the seat stay is connected to the seat hinge, it cannot be disconnected.

  10. Click here

    INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH


    1. Install the spring of the seat stay ball-joint.

    2. Temporarily install the seat hinge and seat stay as a unit.

    3. Raise the under cover.

    4. A01DTG9

      Connect the seat stay to the seat cushion frame.

    5. A01DN0W

      Connect the reclining release handle to the under cover.

    6. Install the 5 screws.

    7. Attach the 10 claws to install the under cover.

    8. Install the pin to the hinge.

    9. Install a new E-ring.

  11. Click here

    INSTALL REAR SEAT HINGE PAWL GUIDE


    1. Attach the 4 claws to install the pawl guide.

      Tip:

      Use the same procedure for both pawl guides.

  12. Click here

    INSTALL SEAT TRACK OPEN LEVER PIN SUB ASSEMBLY


    1. Install the pin as shown in the illustration.

    2. Install the stopper.

      Tip:

      Use the same procedure for both pins.

  13. Click here

    INSTALL RECLINING ADJUSTER INSIDE COVER LH


    1. Attach the 2 claws to install the cover.

    2. Install the 2 screws.

  14. Click here

    INSTALL REAR NO. 2 SEAT CUSHION


    1. Attach the 2 hooks.

    2. A01DPEY

      Attach the guide and 2 claws to install the cover.

    3. Install the 2 screws.

  15. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    1. Attach the 2 hooks.

    2. A01DPEY

      Attach the guide and 2 claws to install the cover.

    3. Install the 2 screws.

  16. Click here

    INSTALL REAR SEAT RECLINING COVER LH


    1. A01DMBU

      Attach the guide and 2 claws to install the cover.

    2. Install the 2 screws.

  17. Click here

    INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. Install the rear No. 1 seat assembly LH (Click here).