FRONT SEAT CUSHION HEATER (for Manual Seat) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE FRONT SEAT ASSEMBLY


    1. Remove the front seat assembly Click here.

  2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    A01DMIAE01
    Text in Illustration
    *1 Protective Tape

    1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the handle.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)

    A01DTA0

    1. Remove the screw and handle.

  4. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. A01DO6O

      Remove the screw.

    2. Using a moulding remover, detach the 4 claws and clip, and then remove the cushion shield.

    3. A01DTS3

      for Driver Side:

      Detach the 5 wire harness clamps and disconnect the 2 connectors.

  5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

    A01DU7M

    1. Using a moulding remover, detach the 3 claws and remove the cushion shield.

  6. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

    A01DNOA

    1. Using a moulding remover, detach the 4 claws and remove the cushion shield.

  7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. for Driver Side:

      Click here

    2. for Front Passenger Side:

      Click here

  8. REMOVE SEAT CUSHION COVER WITH PAD


    1. A01DTTF

      Remove the rubber band from the seat cushion spring.

    2. A01DOTJ

      Disconnect the seat heater connector and detach the wire harness clamp.

    3. A01DMN0E01
      Text in Illustration
      *1 Fastening Tape

      w/ Front Seat Side Airbag:


      1. Detach the fastening tape and open the cover.

      2. Disconnect the airbag wire harness.

    4. A01DN0A

      for Clip Type:

      Using a moulding remover, remove the 2 clips.

    5. A01DQ9A

      for Hook Type:

      Detach the 2 hooks.

    6. A01DMN1

      Disconnect the seat heater connector and detach the 3 wire harness clamps.

    7. Detach the hooks.

      A01DMV4
    8. A01DQ6Y

      for Front Passenger Side:

      Detach the claw and disconnect the connector.

    9. Remove the seat cushion cover with pad.

  9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01DRK1

      Type A:


      1. Remove the hog rings and disconnect the straps.

    2. A01DS9KE01
      Text in Illustration
      *1 Tack Pin

      Type B:


      1. Cut off the tack pins and disconnect the straps.

    3. A01DSQT

      Remove the hog rings and seat cushion cover from the seat cushion pad.

  10. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH

    A01DN1OE01
    Text in Illustration
    *1 Tack Pin

    1. Cut off the tack pins and remove the front seat cushion heater from the front seat cushion cover.