Click here

REAR SEATBACK HEATER (for 60/40 Split Slide Walk-in Seat Type RH Side) INSTALLATION

Click here
Click here Click here
CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Click here
  1. Click here

    INSTALL REAR SEATBACK HEATER ASSEMBLY


    1. Set the rear seatback heater assembly in place with the name stamp side facing the separate type rear seatback cover.

      Table 1. Text in Illustration
      *1 Tack Pin
      *2 Name Stamp

    2. Install the rear seatback heater assembly with 11 new tack pins.

  2. Click here

    INSTALL SEPARATE TYPE REAR SEATBACK COVER


    1. Set the separate type rear seatback cover in place.

    2. A01DR8JE01

      Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 8 new hog rings.

      Table 2. Text in Illustration
      *1 Hog Ring Pliers
      Note:

      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

    3. A01DOJ1

      w/ Seat Heater System:


      1. Connect the rear seatback heater assembly wire harness to the separate type rear seatback pad.

  3. Click here

    INSTALL SEATBACK COVER WITH PAD


    1. w/ Seat Heater System:


      1. A01DTETE01

        Install the wire harness as shown in the illustration.

        Table 3. Text in Illustration
        *a Paint Mark
    2. A01DTORE01

      Attach the hooks.

      Table 4. Text in Illustration
      *1 Hog Ring Pliers
      *2 Hook
      *3 Hog Ring

    3. Using hog ring pliers, install the seatback cover with pad with 14 new hog rings.

      Note:

      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  4. Click here

    INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    1. Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.

  5. Click here

    INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH


    1. Attach the 7 clips to install the rear seatback board carpet assembly RH.

  6. Click here

    INSTALL REAR SEATBACK COVER


    1. Attach the 4 claws to install the rear seatback cover.

  7. Click here

    INSTALL REAR CENTER BACK LOCK CONTROL LEVER


    1. Attach the cable clamp to connect the cable to the rear center back lock control lever.

    2. Move the rear center back lock control lever in the direction of the arrow to attach the guide.

    3. Install the rear center back lock control lever with the 2 screws.

  8. Click here

    INSTALL REAR SEAT COVER CAP


    1. Attach the guide and claw to install the rear seat cover cap.

  9. Click here

    INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    1. A01DN4PE02

      Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly RH.

    2. Install the 2 screws.

  10. Click here

    INSTALL RECLINING ADJUSTER KNOB CAP RH


    1. Attach the guide and claw to install the reclining adjuster knob cap RH.

  11. Click here

    INSTALL SEAT CUSHION COVER WITH PAD


    1. w/ Seat Heater System:


      1. A01DRLA

        Pass the wire harness as shown in the illustration.

      2. A01DTDP

        Connect the 2 rear seat heater connectors.

    2. A01DNVN

      Attach the hooks to install the seat cushion cover with pad.

  12. Click here

    INSTALL REAR SEAT REAR CUSHION MOULDING LH


    1. Attach the 2 guides and 3 claws to install the rear seat rear cushion moulding LH.

    2. Install the screw.

  13. Click here

    INSTALL REAR SEAT CUSHION MOULDING RH


    1. Move the rear seat cushion moulding RH in the direction of the arrow to attach the guide and install the rear seat cushion moulding RH.

    2. Attach the 3 claws and clip to install the rear seat cushion moulding RH.

  14. Click here

    INSTALL RECLINING ADJUSTER RELEASE HANDLE RH


    1. Install the reclining adjuster release handle RH with the 3 screws.

  15. Click here

    INSTALL REAR SEAT UPPER RECLINING COVER RH


    1. Attach the 3 claws to install the rear seat upper reclining cover RH.

  16. Click here

    INSTALL REAR NO. 1 SEAT ASSEMBLY RH

    (Click here)