REAR SEATBACK HEATER (for 60/40 Split Slide Walk-in Seat Type RH Side) REMOVAL

Note

Wear protective gloves. Sharp areas on the parts may injure your hands.


  1. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

    Click here

  2. REMOVE REAR SEAT UPPER RECLINING COVER RH

    A01DRVJE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover RH.

      Tech Tips

      Tape the screwdriver tip before use.

  3. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

    A01DSP0

    1. Remove the 3 screws and reclining adjuster release handle RH.

  4. REMOVE REAR SEAT CUSHION MOULDING RH

    A01DMYQ

    1. Using a clip remover, detach the clip.

    2. Using a moulding remover, detach the 3 claws.

    3. Move the rear seat cushion moulding RH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding RH.

  5. REMOVE REAR SEAT REAR CUSHION MOULDING LH

    A01DNG0

    1. Remove the screw.

    2. Using a moulding remover, detach the 3 claws.

    3. Detach the 2 guides and remove the rear seat rear cushion moulding LH.

  6. REMOVE SEAT CUSHION COVER WITH PAD


    1. A01DTDP

      w/ Seat Heater System:


      1. Disconnect the 2 rear seat heater connectors.

      2. A01DRLA

        Pull out the wire harness as shown in the illustration.

    2. A01DO6L

      Detach the hooks and remove the seat cushion cover with pad.

  7. REMOVE RECLINING ADJUSTER KNOB CAP RH


    1. A01DSCJE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap RH.

      Tech Tips

      Tape the screwdriver tip before use.

  8. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    1. A01DR11

      Remove the 2 screws.

    2. A01DN3ME02

      Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly RH.

  9. REMOVE REAR SEAT COVER CAP

    A01DU6M

    1. Using a screwdriver, detach the claw and guide, and then remove the rear seat cover cap.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE REAR CENTER BACK LOCK CONTROL LEVER

    A01DQG9

    1. Remove the 2 screws.

    2. Move the rear center back lock control lever in the direction of the arrow to detach the guide and remove the rear center back lock control lever.

    3. Detach the cable clamp and disconnect the cable from the rear center back lock control lever.

  11. REMOVE REAR SEATBACK COVER

    A01DSPY

    1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

      Tech Tips

      Tape the screwdriver tip before use.

  12. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH

    A01DU7Q

    1. Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly RH.

  13. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    A01DNOV

    1. Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.

  14. REMOVE SEATBACK COVER WITH PAD


    1. A01DU8QE01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the 14 hog rings and detach the hooks, and then remove the seatback cover with pad.

    2. w/ Seat Heater System:


      1. A01DTET

        Remove the wire harness.

  15. REMOVE SEPARATE TYPE REAR SEATBACK COVER


    1. A01DQP1

      w/ Seat Heater System:


      1. Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.

    2. A01DRF1

      Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.

  16. REMOVE REAR SEATBACK HEATER ASSEMBLY

    A01DNC3E01
    Text in Illustration
    *1 Tack Pin

    1. Cut off the 11 tack pins which fasten the rear seatback heater assembly to the separate type rear seatback cover, and then remove the rear seatback heater assembly from the separate type rear seatback cover.