REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE REAR SEAT UPPER RECLINING COVER LH

    A01DSVIE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    A01DMH2

    1. Remove the 3 screws and reclining adjuster release handle LH.

  3. REMOVE CENTER SEAT HINGE COVER LH

    A01DLY4

    1. Using a clip remover, remove the clip.

    2. Detach the 2 guides and remove the center seat hinge cover LH.

  4. REMOVE REAR SEAT CUSHION MOULDING LH

    A01DR94

    1. Using a clip remover, detach the clip.

    2. Using a moulding remover, detach the 3 claws.

    3. Move the rear seat cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding LH.

  5. REMOVE REAR SEATBACK LOCK STRIKER COVER LH

    A01DTGV

    1. Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover LH.

  6. REMOVE SEAT CUSHION COVER WITH PAD


    1. A01DSJ3

      w/ Seat Heater System:


      1. Disconnect the 2 rear seat heater connectors.

      2. A01DR50

        Pull out the wire harness as shown in the illustration.

    2. A01DSOO

      Detach the hooks.

    3. A01DO80

      Detach the hook and remove the seat cushion cover with pad.

  7. REMOVE REAR NO. 2 SEAT PROTECTOR

    A01DQ7D

    1. Remove the 2 rear No. 2 seat protectors from the separate type rear seat cushion pad.

  8. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER

    A01DNDY

    1. Remove the 14 hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.

  9. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

    A01DSX2E01
    Text in Illustration
    *1 Tack Pin

    1. Cut off the 23 tack pins and remove the rear seat cushion heater assembly from the separate type rear seat cushion cover.

  10. REMOVE REAR SEAT CUSHION EDGE PROTECTOR


    1. Remove the rear seat cushion edge protector from the cushion spring.

  11. REMOVE CENTER SEATBACK ASSEMBLY

    A01DQG0

    1. Remove the 2 bolts and center seatback assembly.

  12. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY


    1. Remove the rear seat center headrest assembly.

  13. REMOVE CENTER SEAT HINGE COVER

    A01DRR4

    1. Using a clip remover, remove the clip.

    2. Detach the 2 guides and remove the center seat hinge cover.

  14. REMOVE REAR SEAT RECLINING BRACKET LH

    A01DSWS

    1. Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and rear seat reclining bracket LH.

  15. REMOVE REAR SEAT RECLINING BRACKET RH


    1. Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and rear seat reclining bracket RH.

  16. REMOVE REAR SEATBACK STAY COVER LH

    A01DNGQ

    1. Using a moulding remover, detach the 3 claws.

    2. Detach the guide and remove the rear seatback stay cover LH.

  17. REMOVE REAR SEATBACK STAY COVER RH


    1. Using a moulding remover, detach the 3 claws.

    2. Detach the guide and remove the rear seatback stay cover RH.

  18. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY


    1. A01DRP4

      Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts and 2 bushes.

    2. A01DSYI

      Remove the nut and rear center seat armrest support LH.

    3. A01DU3Q

      Remove the rear seat center armrest assembly as shown in the illustration.

  19. REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY


    1. A01DTU5

      Remove the 2 screws.

    2. A01DUWA

      Using moulding remover A, detach the 2 claws and remove the rear seat center armrest cup holder sub-assembly.

  20. REMOVE REAR SEATBACK COVER

    A01DSPY

    1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

      Tech Tips

      Tape the screwdriver tip before use.

  21. REMOVE REAR SEATBACK LOCK COVER

    A01DQ21

    1. Using a moulding remover, detach the claw.

    2. Move the cover in the direction of the arrow to detach the clip and 2 guides, and then remove the rear seatback lock cover.

  22. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY

    A01DQKW

    1. Using a clip remover, detach the 5 clips and remove the rear seatback board sub-assembly.

  23. REMOVE SEAT ARMREST COVER


    1. A01DO0T

      Detach the hooks.

    2. A01DULE

      Remove the seat armrest cover with pad.

    3. A01DT9J

      Remove the seat armrest cover from the pad.

  24. REMOVE REAR SEAT HEADREST SUPPORT

    A01DMDS

    1. Detach the 4 claws and remove the 2 rear seat headrest supports.

  25. REMOVE NO. 1 SEATBACK COVER


    1. A01DRWJ

      Using moulding remover A, detach the 2 claws.

    2. A01DQNH

      Detach the guide and remove the No. 1 seatback cover.

  26. REMOVE REAR SEAT LOCK ASSEMBLY LH

    A01DPF9

    1. Detach the clamp and disconnect the wire.

    2. Remove the 2 bolts and rear seat lock assembly LH.

  27. REMOVE REAR NO. 1 SEAT LOCK CONTROL LEVER

    A01DOI7

    1. Remove the rear No. 1 seat lock control lever as shown in the illustration.

  28. REMOVE FOLD SEATBACK WIRE

    A01DSIK

    1. Detach the 2 claws and remove the fold seatback wire.

  29. REMOVE COAT HOOK CAP

    A01DUC9E01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 2 claws and guide, and then remove the coat hook cap.

      Tech Tips

      Tape the screwdriver tip before use.

  30. REMOVE CENTER NO. 2 SEATBACK COVER

    A01DSZJ

    1. Remove the 3 screws and center No. 2 seatback cover.

  31. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

    A01DR92

    1. Remove the bolt and rear No. 1 seat inner belt assembly LH and disconnect the No. 1 seat 3 point type belt assembly LH.

  32. REMOVE RECLINING ADJUSTER KNOB CAP LH

    A01DRFLE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap LH.

      Tech Tips

      Tape the screwdriver tip before use.

  33. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH


    1. A01DPON

      Remove the 2 screws.

    2. A01DN1KE02

      Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly LH.

  34. REMOVE SEAT BELT ANCHOR COVER CAP


    1. A01DMP0E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws and remove the seat belt anchor cover cap.

      Tech Tips

      Tape the screwdriver tip before use.

  35. REMOVE REAR SEAT SHOULDER BELT COVER


    1. Disconnect the outer belt from the rear seat shoulder belt cover.

    2. A01DUWH

      Detach the 2 claws and 2 guides, and then remove the rear seat shoulder belt cover.

  36. REMOVE REAR SEATBACK COVER

    A01DSPY

    1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

      Tech Tips

      Tape the screwdriver tip before use.

  37. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH

    A01DPQ6

    1. Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly LH.

  38. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

    A01DNOV

    1. Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.

  39. REMOVE SEATBACK COVER WITH PAD


    1. A01DN78E01
      Text in Illustration
      *1 Hook
      *2 Hog Ring

      Remove the 10 hog rings and detach the hooks, and then remove the seatback cover with pad.

    2. A01DUW0

      Disconnect the outer belt from the seatback cover with pad.

    3. w/ Seat Heater System:


      1. A01DS5J

        Remove the wire harness.

  40. REMOVE SEPARATE TYPE REAR SEATBACK COVER


    1. A01DQ6N

      w/ Seat Heater System:


      1. Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.

    2. A01DU2F

      Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.

  41. REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

    A01DNC3E01
    Text in Illustration
    *1 Tack Pin

    1. Cut off the 11 tack pins which fasten the rear seatback heater assembly to the separate type rear seatback cover, and then remove the rear seatback heater assembly from the separate type rear seatback cover.

  42. REMOVE REAR SEATBACK EDGE PROTECTOR


    1. Remove the rear seatback edge protector from the rear seatback frame sub-assembly LH.

  43. REMOVE REAR SEAT INNER RECLINING COVER LH

    A01DT9A

    1. Remove the 2 screws.

    2. Detach the guide and remove the rear seat inner reclining cover LH.

  44. REMOVE RECLINING ADJUSTER INSIDE COVER LH

    A01DSV0

    1. Remove the 2 screws.

    2. Detach the 2 claws and remove the reclining adjuster inside cover LH.

  45. REMOVE REAR SEAT REAR CUSHION MOULDING LH

    A01DPT8

    1. Using a clip remover, detach the clip.

    2. Using moulding remover A, detach the 4 claws.

    3. Move the rear seat rear cushion moulding LH in the direction of the arrow to detach the guide and remove the rear seat rear cushion moulding LH.

  46. REMOVE CAP

    A01DQI8

    1. Detach the 2 claws and remove the cap.

  47. REMOVE REAR SEAT RECLINING COVER INNER LH

    A01DMCS

    1. Detach the claw and guide, and then remove the rear seat reclining cover inner LH.

  48. REMOVE REAR SEAT CUSHION SPRING DAMPER

    A01DMWQ

    1. Remove the 2 nuts and rear seat cushion spring damper.

  49. REMOVE REAR SEAT SHOULDER BELT GUIDE

    A01DOHK

    1. Detach the claw and guide, and then remove the rear seat shoulder belt guide.

  50. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A01DSJW

    1. Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.

  51. REMOVE REAR SEAT RECLINING CONTROL CABLE


    1. Cut off the 4 cable ties.

      A01DO9Q

    2. Detach the 3 cable clamps and disconnect the cable, and then remove the rear seat reclining control cable.

      A01DNMX

  52. REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE


    1. Detach the 3 cable clamps and disconnect the cable, and then remove the rear No. 2 seat reclining control cable.

      A01DM54

  53. REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY LH

    A01DP08

    1. Remove the 2 nuts and rear back lock control lever sub-assembly LH.

  54. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)


    1. A01DR0R

      Disconnect the connector.

    2. Detach the 2 clamps and remove the seat heater control sub-assembly.

  55. REMOVE REAR SEAT WIRE LH (w/ Seat Heater System)


    1. A01DQRQ

      Detach the claw and disconnect the rear seat wire connector.

    2. Detach the clamp and remove the rear seat wire LH.

  56. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY LH

    A01DSFW

    1. Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts.

    2. Remove the 2 bolts and rear seatback frame sub-assembly LH.

  57. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH

    A01DNHI

    1. Remove the 6 nuts and rear seat cushion frame sub-assembly LH.

  58. REMOVE REAR SEAT TRACK ADJUSTING HANDLE LH

    A01DPRF

    1. Slide the slide rail to the rearmost position.

    2. Using a small screwdriver, push down the handle stopper to detach the claw and remove the rear seat track adjusting handle LH.

      Tech Tips

      Insert the screwdriver into the hole shown in the illustration while looking into the hole.