POWER SEAT SWITCH (for Rear No. 2 Seat) INSPECTION


  1. INSPECT REAR POWER SEAT SWITCH (for LH Side)


    1. A01DP78E01
      Text in Illustration
      *1 UP Switch
      *2 DOWN Switch
      *a

      Component without harness connected

      (Rear Power Seat Switch Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      4 (FWD) - 6 (E) UP switch pressed Below 1 Ω
      5 (BACK) - 6 (E) DOWN switch pressed

      If the result is not as specified, replace the rear power seat switch assembly.

    2. A01DUGFE01
      Text in Illustration
      *a

      Component without harness connected

      (Rear Power Seat Switch Assembly)

      Apply battery voltage to the switch connector and check that the power seat switch illuminates.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → 7 (ILL+)

      Battery negative (-) → 2 (ILL-)

      		 Illumination illuminates

      If the result is not as specified, replace the rear power seat switch assembly.

  2. INSPECT REAR POWER SEAT SWITCH (for RH Side)


    1. A01DP78E01
      Text in Illustration
      *1 UP Switch
      *2 DOWN Switch
      *a

      Component without harness connected

      (Rear Power Seat Switch Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      4 (FWD) - 6 (E) UP switch pressed Below 1 Ω
      5 (BACK) - 6 (E) DOWN switch pressed

      If the result is not as specified, replace the rear power seat switch assembly.

    2. A01DUGFE01
      Text in Illustration
      *a

      Component without harness connected

      (Rear Power Seat Switch Assembly)

      Apply battery voltage to the switch connector and check that the power seat switch illuminates.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → 7 (ILL+)

      Battery negative (-) → 2 (ILL-)

      		 Illumination illuminates

      If the result is not as specified, replace the rear power seat switch assembly.

  3. INSPECT NO. 1 FOLD SEAT SWITCH ASSEMBLY


    1. A01DULGE01
      Text in Illustration
      *1 RETURN RH Switch
      *2 FOLD RH Switch
      *3 RETURN LH Switch
      *4 FOLD LH Switch
      *a

      Component without harness connected

      (No. 1 Fold Seat Switch Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 (RTNL) - 7 (E) RETURN LH switch pressed Below 1 Ω
      6 (FLDL) - 7 (E) FOLD LH switch pressed
      3 (RTNR) - 7 (E) RETURN RH switch pressed
      8 (FLDR) - 7 (E) FOLD RH switch pressed

      If the result is not as specified, replace the No. 1 fold seat switch assembly.

    2. A01DN4JE01
      Text in Illustration
      *a

      Component without harness connected

      (No. 1 Fold Seat Switch Assembly)

      Apply battery voltage to the switch connector and check that the fold seat switch illuminates.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → 5 (+B)

      Battery negative (-) → 7 (E)

      		 Illumination illuminates

      If the result is not as specified, replace the No. 1 fold seat switch assembly.