REAR AIRBAG SENSOR (for 3 Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. Click here

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR NO. 1 SEAT ASSEMBLY


    1. for 60/40 Split Double-folding Seat Type LH Side:


      1. Remove the rear No. 1 seat assembly Click here.

    2. for 60/40 Split Double-folding Seat Type RH Side:


      1. Remove the rear No. 1 seat assembly Click here.

    3. for 60/40 Split Tumble Seat Type LH Side:


      1. Remove the rear No. 1 seat assembly Click here.

    4. for 60/40 Split Tumble Seat Type RH Side:


      1. Remove the rear No. 1 seat assembly Click here.

    5. for 60/40 Split Slide Walk-in Seat Type LH Side:


      1. Remove the rear No. 1 seat assembly Click here.

    6. for 60/40 Split Slide Walk-in Seat Type RH Side:


      1. Remove the rear No. 1 seat assembly Click here.

  3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    A01DNTTE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    A01DMY1

    1. Remove the front door opening trim weatherstrip.

  5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  6. REMOVE MAT SET PLATE COVER

    A01DNTXE01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for all mat set plate covers.


    1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

      Tech Tips

      Tape the screwdriver tip before use.

  7. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

    A01DSF1

    1. Remove the 5 screws.

    2. Detach the 6 claws and remove the rear floor mat rear support plate.

  8. REMOVE QUARTER TRIM COVER HOLE LH

    A01DOG6

    1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.

  9. REMOVE REAR FLOOR CARPET ASSEMBLY

    A01DTIS

    1. Remove the rear floor carpet.

  10. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    A01DNOJ

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Remove the luggage compartment trim hook by turning it clockwise.

  11. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    A01DMF1E01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for the other tonneau cover holder cap.


    1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  12. REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    A01DTB0E01
    Text in Illustration
    *1 Protective tape

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  13. REMOVE OUTER LAP BELT COVER

    A01DRK4

    Tech Tips

    Use the same procedure for the other outer lap belt anchor cover.


    1. Detach the 3 claws and remove the outer lap belt anchor cover.

  14. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

    A01DO0R

    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A01DOAG

      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    3. Remove the 3 bolts and 2 screws.

    4. Detach the 9 claws and 12 clips and remove the deck trim side panel.

      A01DR76

  15. REMOVE REAR AIRBAG SENSOR LH


    1. A01DP88

      Remove the nut and rear airbag sensor.

    2. Disconnect the connector.