REAR AIRBAG SENSOR (for 5 Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. Click here

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. for Manual Seat Type LH Side:


      1. Remove the rear No. 2 seat assembly Click here.

    2. for Power Seat Type LH Side:


      1. Remove the rear No. 2 seat assembly Click here.

    3. for Face to Face Seat Type:


      1. Remove the rear No. 2 seat assembly Click here.

  3. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

    A01DM5QE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for all rear No. 1 floor step covers.


    1. Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

    A01DMHG

    1. Remove the 2 bolts and quarter scuff plate.

  5. REMOVE REAR DOOR SCUFF PLATE LH

    A01DP89E01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the rear door scuff plate.

    2. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides and remove the rear door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    A01DU3A

    1. Remove the rear door opening trim weatherstrip.

  7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  8. REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

    A01DOZC

    Tech Tips

    Use the same procedure for the other front luggage compartment trim cover.


    1. Detach the 4 claws and remove the cap.

    2. A01DTUCE01
      Text in Illustration
      *1 Luggage Hold Belt Striker

      Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.

  9. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

    A01DQ5S

    1. Detach the clip and remove the No. 1 deck board.

  10. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

    A01DMAR

    1. Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.

  11. REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)

    A01DQSE

    1. Remove the 3 bolts and floor side rail.

  12. REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)


    1. Detach the 4 claws and remove the rear floor carpet.

      A01DNAME01
      Text in Illustration
      *A w/o Deck Rail *B w/ Deck Rail
      *C for Face to Face Seat Type - -

  14. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

    A01DRNL

    Tech Tips

    Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.


    1. Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.

  15. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    A01DNOJ

    Tech Tips

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Remove the luggage compartment trim hook by turning it clockwise.

  16. REMOVE NO. 1 TONNEAU COVER HOLDER CAP

    A01DN3TE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other No. 1 tonneau cover holder cap.


    1. Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.

      Tech Tips

      Tape the screwdriver tip before use.

  17. REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

    A01DSSQE01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for all assist grip plugs.


    1. Using a screwdriver, detach the 2 claws and remove the assist grip plug.

      Tech Tips

      Tape the screwdriver tip before use.

  18. REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

    A01DP0H

    Tech Tips

    Use the same procedure for the other assist grip.


    1. Remove the 2 bolts and assist grip.

  19. REMOVE FRONT DECK SIDE TRIM COVER

    A01DTB0E01
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for the other front deck side trim cover.


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tech Tips

      Tape the screwdriver tip before use.

  20. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. w/o Rear No. 2 Seat:


      1. A01DSFL

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. A01DUCB

        Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.

      3. Remove the 4 bolts and 2 screws.

      4. Detach the 5 clips and 8 claws.

      5. Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.

        A01DSVK

    2. w/ Rear No. 2 Seat:


      1. A01DSFL

        Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

      2. A01DNKI

        Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.

      3. Remove the 2 bolts and 2 screws.

      4. Detach the 4 clips and 8 claws and remove the deck trim side panel.

        A01DQR3

  21. REMOVE REAR AIRBAG SENSOR LH


    1. A01DU8H

      Remove the nut and rear airbag sensor.

    2. Disconnect the connector.