FRONT SEAT SIDE AIRBAG ASSEMBLY REMOVAL

CAUTION:


  • Be sure to read Precaution thoroughly before servicing Click here.

  • Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

  • If the side airbag was deployed, replace the front seat side airbag assembly, separate type front seatback spring assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

    for Manual Seat: Click here

    for Power Seat: Click here

    for Walk in Seat Type: Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side. (for Manual Seat, Power Seat)

  • The procedure listed below is for the RH side. (for Walk in Seat Type)


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. Click here

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT SEAT HEADREST ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here

    for Walk in Seat Type: Click here

  3. REMOVE FRONT SEAT INNER TRACK BRACKET COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  4. REMOVE FRONT SEAT OUTER TRACK BRACKET COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  5. REMOVE INNER SEAT TRACK BRACKET COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  6. REMOVE SEAT TRACK COVER LH

    for Manual Seat: Click here

    for Power Seat: Click here

  7. REMOVE FRONT SEAT INNER TRACK BRACKET COVER RH (for Walk in Seat Type)

    A01DQK2

    1. Operate the seat track adjusting handle to move the seat to the rearmost position.

    2. Using a moulding remover, detach the 2 claws and remove the cover.

  8. REMOVE FRONT SEAT OUTER TRACK BRACKET COVER RH (for Walk in Seat Type)

    A01DR13

    1. Using a moulding remover, detach the 2 claws.

    2. Move the cover in the direction of the arrow to detach the guide and remove the cover.

  9. REMOVE INNER SEAT TRACK BRACKET COVER RH (for Walk in Seat Type)

    A01DRES

    1. Operate the seat track adjusting handle to move the seat to the foremost position.

    2. Using a moulding remover, detach the 2 claws.

    3. Move the cover in the direction of the arrow to detach the 2 guides and remove the cover.

  10. REMOVE SEAT TRACK COVER RH (for Walk in Seat Type)

    A01DSGH

    1. Using a moulding remover, detach the 2 claws.

    2. Move the cover in the direction of the arrow to detach the 2 guides and remove the cover.

  11. REMOVE FRONT SEAT ASSEMBLY

    for Manual Seat: Click here

    for Power Seat: Click here

    for Walk in Seat Type: Click here

  12. DISCONNECT FRONT SEAT SIDE AIRBAG ASSEMBLY


    1. for Manual Seat, Power Seat:


      1. A01DTTF

        Remove the rubber band from the seat cushion spring.

      2. A01DSY5E01
        Text in Illustration
        *1 Fastening Tape

        Detach the claw and disconnect the airbag connector.

      3. Detach the 3 airbag wire harness clamps.

      4. Detach the fastening tape and open the cover.

      5. Disconnect the airbag wire harness.

    2. for Walk in Seat Type:


      1. A01DSPX

        Remove the rubber band from the seat cushion spring.

      2. A01DNAHE01
        Text in Illustration
        *1 Fastening Tape

        Detach the claw and disconnect the airbag connector.

      3. Detach the 4 airbag wire harness clamps.

      4. Detach the fastening tape and open the cover.

      5. Disconnect the airbag wire harness.

  13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

    Tech Tips

    Use the same procedure for the RH and LH sides.


    1. A01DOTJ

      w/ Seat Heater System:

      Disconnect the seat heater connector and detach the wire harness clamp.

    2. A01DO50

      Remove the 3 hog rings.

    3. Open the 2 fasteners, and then open the front seatback cover.

      A01DPT9E01
      Text in Illustration
      *A for Cloth Seat *B for Leather Seat
    4. A01DPBF

      Remove the nut and front seatback cover bracket.

    5. A01DUCD

      Using a screwdriver, detach the 4 claws to remove the 2 front seat headrest supports.

    6. Remove the separate type seatback cover with pad.

  14. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY

    CAUTION:

    When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.

    Tech Tips

    Use the same procedure for the RH and LH sides.


    1. A01DUSO

      Detach the 2 clamps.

    2. A01DLYX

      Remove the 2 nuts and front seat side airbag assembly.

      CAUTION:


      • The nuts must not be reused.

      • Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.