METER / GAUGE SYSTEM OPERATION CHECK


  1. INSPECT INDICATOR/WARNING LIGHT


    1. Check the following indicators and warning lights.

      Indicator/Warning Light Switch Condition Specified Condition
      BRAKE warning light Ignition switch off → ON Comes on for 3 seconds
      ABS warning light
      SLIP indicator light*1
      TRC OFF indicator light*1
      VSC OFF indicator light*1
      CRAWL indicator light*3
      Downhill assist control indicator light*4
      KDSS indicator light*5
      Eco driving indicator Light*6
      Oil Maintenance warning indicator light*2, *7, *8
      OIL LEVEL indicator light*8, *9
      T-BELT indicator light*2, *8, *10
      FUEL FILTER & SEDIMENTER indicator light*2, *8, *11
      SEDIMENTER indicator light*2, *9, *10
      SPEED LIMIT indicator light*12
      PCS indicator light*13
      PPS warning light*1
      Master warning light*15
      BSM indicator light*17
      Headlight beam level control system warning light*14
      LED headlight warning light*14
      Tire pressure warning light*18
      SRS warning light Ignition switch off → ON Comes on for 6 seconds
      CHARGE warning light Ignition switch off → ON

      • Illuminates when ignition switch turned to ON

      • Turns off when engine started
      OIL PRESSURE warning light
      A/T TEMP warning light*6
      MIL
      SIL indicator light*7, *8, *16

      • *1: except 5L-E

      • *2: for Analog Meter

      • *3: w/ Crawl Control

      • *4: w/ Downhill Assist Control

      • *5: w/ Kinetic Dynamic Suspension System

      • *6: for Automatic Transmission

      • *7: for Europe

      • *8: for 1KD-FTV

      • *9: for Europe 1KD-FTV

      • *10: for 5L-E

      • *11: except Europe

      • *12: for Middle East

      • *13: w/ Pre-crash Safety System

      • *14: for LED Headlight

      • *15: for Optitron Meter

      • *16: for Manual Transmission

      • *17: w/ Blind Spot Monitor System

      • *18: w/ Tire Pressure Monitor System

  2. INSPECT SPEEDOMETER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

      If the result is not as specified, the speedometer may have a malfunction.

      Note

      Do not use worn, underinflated or overinflated tires as the speedometer reading will be inaccurate.

    5. Check the deflection width of the speedometer indicator.

    6. INSPECT TACHOMETER


      1. Connect a tune-up tachometer and start the engine.

      2. Compare the test results with the tachometer indicator.

      7. If the result is not as specified, the tachometer may have a malfunction.

    7. INSPECT METER/GAUGE


      1. Connect the intelligent tester to the DLC3.

      2. Perform the Active Test Click here.

    8. INSPECT WARNING/INDICATOR LIGHT


      1. Connect the intelligent tester to the DLC3.

      2. Perform the Active Test Click here.

    9. INSPECT MULTI-INFORMATION DISPLAY (for Analog Meter)


      1. Connect the intelligent tester to the DLC3.

      2. Perform the Active Test Click here.

        Tech Tips

        If this Active Test is being performed and the ignition switch is turned off and then to ON, the clock and ODO/TRIP display background may turn white. If this occurs, end the Active Test and turn the ignition switch off.

    10. INSPECT MULTI-INFORMATION DISPLAY (for Optitron Meter)


      1. Connect the intelligent tester to the DLC3.

      2. Perform the Active Test Click here.

        Tech Tips

        If this Active Test is being performed and the ignition switch is turned off and then to ON, the ODO/TRIP display background may turn white. If this occurs, end the Active Test and turn the ignition switch off.