ROOM LIGHT SWITCH REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE DOOR SCUFF PLATE ASSEMBLY LH (for LHD)

    A01DNTTE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  2. REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD)

    Tech Tips

    Use the same procedure described for the LH side.

  3. REMOVE COWL SIDE TRIM BOARD LH (for LHD)

    A01DQEI

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  4. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

    Tech Tips

    Use the same procedure described for the LH side.

  5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A01DSZY

    1. for LHD:


      1. Remove the screw.

      2. Detach the 2 clips and 2 guides and remove the No. 1 instrument panel under cover.

      3. Disconnect each connector.

    2. A01DORU

      for RHD:


      1. Remove the screw.

      2. Detach the 3 clips and 2 guides and remove the No. 1 instrument panel under cover.

      3. Disconnect each connector.

  6. REMOVE INSTRUMENT SIDE PANEL LH (for LHD)

    A01DNBCE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel.

    2. Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.

  7. REMOVE INSTRUMENT SIDE PANEL RH (for RHD)

    A01DUSZE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel.

    2. Using a moulding remover, detach the 5 clips, claw, and 3 guides.

    3. Disconnect the connector and remove the instrument side panel.

  8. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

    A01DM0OE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument cluster finish panel ornament.

    2. Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.

  9. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

    A01DREC

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish plate garnish.

  10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    A01DP35

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish panel.

  11. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

    A01DT5YE01

    1. Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A01DOV5

      w/o Knee Airbag:


      1. Remove the 2 bolts <C>.

      2. Detach the 7 clips.

      3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

    3. A01DPFD

      w/ Knee Airbag:


      1. Remove the 2 bolts <C>.

      2. Detach the 14 clips.

      3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

  12. REMOVE ROOM LIGHT SWITCH ASSEMBLY (for LHD)


    1. A01DRWF

      Detach the 2 claws and remove the switch.

  13. REMOVE ROOM LIGHT SWITCH ASSEMBLY (for RHD)


    1. A01DR0M

      Detach the 2 claws and remove the switch.