SECURITY HORN ASSEMBLY (w/ Built-in Battery type) INSTALLATION

INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for 3 Door)

1. Connect the connector.

2. Attach the 9 claws and 11 clips to install the deck trim side panel.

3. Install the 3 bolts and 2 screws.

4. Install the rear No. 1 seat outer belt floor anchor with the bolt.

   Torque:

   42 N*m  { 428 kgf*cm, 31 ft.*lbf }

5. Install the front seat outer belt floor anchor with the bolt.

   Torque:

   42 N*m  { 428 kgf*cm, 31 ft.*lbf }

INSTALL OUTER LAP BELT ANCHOR COVER (for 3 Door)

1. Attach the 3 claws to install the outer lap belt anchor cover.

INSTALL QUARTER TRIM POCKET TRAY (for 3 Door)

1. Attach the 6 claws and 2 guides to install the quarter trim pocket tray.

INSTALL FRONT DECK SIDE TRIM COVER (for 3 Door)

1. Attach the 2 claws to install the front deck side trim cover.

INSTALL NO. 1 TONNEAU COVER HOLDER CAP (for 3 Door)

1. Attach the 2 claws to install the tonneau cover holder cap.

INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for 3 Door)

1. Install the No. 1 luggage compartment trim hook so that it is positioned horizontally.

INSTALL REAR FLOOR CARPET ASSEMBLY (for 3 Door)

1. Install the rear floor carpet.

INSTALL QUARTER TRIM COVER HOLE RH (for 3 Door)

INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (for 3 Door)

1. Attach the 6 claws to install the rear floor mat rear support plate.

2. Install the 5 screws.

INSTALL MAT SET PLATE COVER (for 3 Door)

1. Attach the 2 claws to install the mat set plate cover.

INSTALL TONNEAU COVER ASSEMBLY (for 3 Door)

1. Install the tonneau cover.

INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for 3 Door)

INSTALL DOOR SCUFF PLATE ASSEMBLY RH (for 3 Door)

INSTALL REAR SIDE NO. 2 AIR DUCT

1. Install the duct with the 2 clips and attach the clamp.

INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

1. w/o Rear No. 2 Seat:

   
   

   1. Connect each connector.

   2. Pass the rear seatback lock control lever base through the deck trim side panel.

   3. Attach the 5 clips and 8 claws to install the deck trim side panel.

   4. Install the 4 bolts and screw.

   5. Attach the 6 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.

   6. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:

      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

2. w/ Rear No. 2 Seat:

   
   

   1. Connect each connector.

   2. Attach the 4 clips and 8 claws to install the deck trim side panel.

   3. Install the 2 bolts and screw.

   4. Install the rear No. 2 seat outer belt floor anchor with the bolt.

      Torque:

      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

   5. Install the rear No. 1 seat outer belt floor anchor with the bolt.

      Torque:

      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)

1. Install the assist grip with the 2 bolts.

INSTALL ASSIST GRIP PLUG (w/ Rear No. 2 Seat)

1. Attach the 2 claws to install the assist grip plug.

INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

1. Attach the 2 claws to install the front deck side trim cover

INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

1. Attach the 2 claws to install the No. 1 tonneau cover holder cap.

INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

1. Install the No. 1 luggage compartment trim hook by turning it clockwise.

INSTALL REAR NO.1 SEAT OUTER LAP BELT ANCHOR COVER

1. Attach the 3 claws to install the rear No. 1 seat outer lap belt anchor cover.

INSTALL REAR FLOOR CARPET ASSEMBLY

INSTALL FLOOR SIDE RAIL RH (w/ Deck Rail)

INSTALL FLOOR SIDE RAIL LH (w/ Deck Rail)

1. Install the floor side rail with the 3 bolts.

INSTALL REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)

1. Attach the 5 clips and 4 claws to install the rear floor mat rear support plate.

INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)

1. Attach the clip to install the No. 1 deck board.

INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

Text in Illustration

*1	Luggage Hold Belt Striker

Tech Tips

Use the same procedure for the other front luggage compartment trim cover.

1. Install the luggage hold belt striker and front luggage compartment trim cover with the bolt.

2. Attach the 4 claws to install the cap.

INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

1. Install the tonneau cover.

INSTALL OUTER LAP BELT ANCHOR COVER

1. Attach the 3 claws to install the outer lap belt anchor cover

INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

INSTALL REAR DOOR SCUFF PLATE RH

INSTALL QUARTER SCUFF PLATE INNER RH

INSTALL REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

1. Attach the 2 claws to install the rear No. 1 floor step cover.