ENTRY AND START SYSTEM (for Entry Function) Front Passenger Side Door Entry Lock Function does not Operate

DESCRIPTION

If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter is normal. The malfunctioning part may be an entry lock sensor circuit (front door outside handle assembly [for front passenger side] → certification ECU).

WIRING DIAGRAM

A01DP84E04

INSPECTION PROCEDURE

Note


  • The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

  • Check that there are no electrical key transmitters in the vehicle.

  • Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output Click here.

  • When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

  • Before replacing the certification ECU, refer to the Service Bulletin.

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. Read the Data List according to the display on the intelligent tester.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      FR Door Lock Pos*1 Front RH side door lock position switch signal / UNLOCK or LOCK

      UNLOCK: Front RH side door unlocked

      LOCK: Front RH side door locked

      		 -
      FL Door Lock Pos*2 Front LH side door lock position switch signal / UNLOCK or LOCK

      UNLOCK: Front LH side door unlocked

      LOCK: Front LH side door locked

      		 -

      • *1: for LHD

      • *2: for RHD

      OK
      On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Front Passenger Door Lock/Unlock Functions do not Operate) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)


    1. Using the intelligent tester, read the Data List Click here.

      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P-Door Trigger Switch Front passenger side door lock sensor / ON or OFF

      ON: Front passenger side door lock sensor touched

      OFF: Front passenger side door lock sensor not touched

      		 -
      OK
      "ON" (lock sensor is touched) and "OFF" (lock sensor is not touched) appear on the screen.

    NG

    CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU) Click here

    OK

    REPLACE CERTIFICATION ECU

  4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)


    1. Disconnect the N1*1 or O1*2 handle connector.

      *1: for LHD

      *2: for RHD

    2. Disconnect the G38 ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      N1-1 (TRG+) - G38-19 (TSW2) Always Below 1 Ω
      G38-19 (TSW2) - Body ground Always 10 kΩ or higher
      G38-15 (E) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      O1-1 (TRG+) - G38-19 (TSW2) Always Below 1 Ω
      G38-19 (TSW2) - Body ground Always 10 kΩ or higher
      G38-15 (E) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (LOCK SENSOR)


    1. Measure the voltage according to the value(s) in the table below.

      A01DOFJE23
      Text in Illustration
      *a

      Component with harness connected

      (Certification ECU)

      		 - -
      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G38-19 (TSW2) - G38-15 (E) Engine switch off, all doors closed and lock sensor (for front passenger side) off → on Pulse generation → Below 2 V

    NG

    REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE) Click here

    OK

    REPLACE CERTIFICATION ECU