Click here

DOOR CONTROL RECEIVER (for 3 Door) REMOVAL

Click here
Click here Click here
  1. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Click here

    REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)


    1. for LH Side:

      Remove the rear No. 1 seat assembly (Click here).

    2. for RH Side:

      Remove the rear No. 1 seat assembly (Click here).

  3. Click here

    REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  4. Click here

    REMOVE MAT SET PLATE COVER

    Tip:

    Use the same procedure for all mat set plate covers.


    1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.

      Tip:

      Tape the screwdriver tip before use.

      Table 1. Text in Illustration
      *1 Protective tape
  5. Click here

    REMOVE REAR FLOOR MAT REAR SUPPORT PLATE


    1. Remove the 5 screws.

    2. Detach the 6 claws and remove the rear floor mat rear support plate.

  6. Click here

    REMOVE QUARTER TRIM COVER HOLE LH


    1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.

  7. Click here

    REMOVE REAR FLOOR CARPET ASSEMBLY


    1. Remove the rear floor carpet.

  8. Click here

    REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tip:

    Use the same procedure for the other No. 1 luggage compartment trim hook.


    1. Remove the luggage compartment trim hook by turning it clockwise.

  9. Click here

    REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)

    Tip:

    Use the same procedure for the other tonneau cover holder cap.


    1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.

      Tip:

      Tape the screwdriver tip before use.

      Table 2. Text in Illustration
      *1 Protective tape
  10. Click here

    REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

    Tip:

    Use the same procedure for the other front deck side trim cover.


    1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.

      Tip:

      Tape the screwdriver tip before use.

      Table 3. Text in Illustration
      *1 Protective tape
  11. Click here

    REMOVE QUARTER TRIM POCKET TRAY


    1. Put protective tape around the quarter trim pocket tray.

    2. Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.

      Tip:

      Tape the screwdriver tip before use.

      Table 4. Text in Illustration
      *1 Protective tape
  12. Click here

    REMOVE OUTER LAP BELT ANCHOR COVER

    Tip:

    Use the same procedure for the other outer lap belt anchor cover.


    1. Detach the 3 claws and remove the outer lap belt anchor cover.

  13. Click here

    REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the bolt and disconnect the front seat outer belt floor anchor.

    2. A01DOAG

      Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.

    3. Remove the 3 bolts and 2 screws.

    4. A01DR76

      Detach the 9 claws and 12 clips and remove the deck trim side panel.

  14. Click here

    REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH


    1. Detach the 7 clips.

    2. A01DOBV

      Detach the 4 claws and 2 guides, pass the rear No. 1 seat belt floor anchor through the rear quarter trim panel and remove the rear quarter trim panel.

  15. Click here

    REMOVE DOOR CONTROL RECEIVER


    1. A01DQLSE01

      Disconnect the connector.

      Table 5. Text in Illustration
      *A w/o Entry and Start System
      *B w/ Entry and Start System

    2. Remove the bolt and receiver.