QUARTER TRIM SPEAKER (for 3 Door) REMOVAL

Tech Tips

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

PRECAUTION

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE REAR NO. 1 SEAT ASSEMBLY
1. for 60/40 Split Tumble Seat Type LH Side:
  
  Click here
2. for 60/40 Split Tumble Seat Type RH Side:
  
  Click here
REMOVE DOOR SCUFF PLATE ASSEMBLY LH
Text in Illustration

*1 Protective Tape
1. Put protective tape around the door scuff plate.
2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Remove the front door opening trim weatherstrip.
REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
1. Remove the tonneau cover.
REMOVE MAT SET PLATE COVER
Text in Illustration

*1 Protective tape

Tech Tips

Use the same procedure for all mat set plate covers.
1. Using a screwdriver, detach the 2 claws and remove the mat set plate cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE REAR FLOOR MAT REAR SUPPORT PLATE
1. Remove the 5 screws.
2. Detach the 6 claws and remove the rear floor mat rear support plate.
REMOVE QUARTER TRIM COVER HOLE LH
1. Detach the 2 claws and 2 guides and remove the quarter trim cover hole.
REMOVE REAR FLOOR CARPET ASSEMBLY
1. Remove the rear floor carpet.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Tech Tips

Use the same procedure for the other No. 1 luggage compartment trim hook.
1. Remove the luggage compartment trim hook by turning it clockwise.
REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
Text in Illustration

*1 Protective tape

Tech Tips

Use the same procedure for the other tonneau cover holder cap.
1. Using a screwdriver, detach the 2 claws and remove the tonneau cover holder cap.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
Text in Illustration

*1 Protective tape

Tech Tips

Use the same procedure for the other front deck side trim cover.
1. Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE QUARTER TRIM POCKET TRAY
Text in Illustration

*1 Protective tape
1. Put protective tape around the quarter trim pocket tray.
2. Using a screwdriver, detach the 6 claws and 2 guides, and remove the quarter trim pocket tray.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE OUTER LAP BELT ANCHOR COVER
Tech Tips

Use the same procedure for the other outer lap belt anchor cover.
1. Detach the 3 claws and remove the outer lap belt anchor cover.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
1. Remove the bolt and disconnect the front seat outer belt floor anchor.
2. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
3. Remove the 3 bolts and 2 screws.
4. Detach the 9 claws and 12 clips and remove the deck trim side panel.
REMOVE REAR SPEAKER SET
1. Disconnect the speaker connector.
2. Remove the 3 screws.
3. Detach the 2 claws and remove the rear speaker set.
  
  Note
  
  Do not touch the cone of the speaker.
REMOVE NO. 2 SPEAKER BRACKET
1. Detach the clamp.
2. Remove the 3 bolts and No. 2 speaker bracket.