POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM, Diagnostic DTC:B2610

DTC Code DTC Name
B2610 Tilt Position Sensor or Tilt Motor Circuit Malfunction

DESCRIPTION

The tilt motor is operated by the power source voltage supplied from the multiplex tilt and telescopic ECU and tilts the steering column up and down. The tilt position sensor (Hall IC) in the tilt motor detects the tilt angle of the steering column and outputs a signal to the multiplex tilt and telescopic ECU based on that angle.

Tech Tips

The limit positions can be confirmed on the Data List screen of the intelligent tester.

DTC Code Detection Condition Trouble Area
B2610 The tilt operation stops within the operation range while operating.

  • Harness or connector

  • Tilt position sensor or tilt motor

  • Multiplex tilt and telescopic ECU

WIRING DIAGRAM

A01DUQNE01

INSPECTION PROCEDURE

Note

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TILT OPERATION)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the steering wheel tilts up and down.

      Tilt & Telescopic
      Tester Display Test Part Control Range Diagnostic Note
      Tilt Operation Tilt operation UP/DOWN -
      Result
      Result Proceed to
      Steering wheel does not tilt up/down. A
      Steering wheel tilts up/down. B

    B

    CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR) Click here

    A

  2. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BATTERY)


    1. A01DO8OE13
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Multiplex Tilt and Telescopic ECU)

      Disconnect the G116 multiplex tilt and telescopic ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G116-2 (+B) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)


    1. A01DO8OE14
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Multiplex Tilt and Telescopic ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G116-11 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT MOTOR)


    1. Disconnect the G122 tilt motor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G116-10 (TIM+) - G122-1 (TIM+) Always Below 1 Ω
      G116-1 (TIM-) - G122-2 (TIM-)
      G116-10 (TIM+) - Body ground Always 10 kΩ or higher
      G116-1 (TIM-) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK TILT MOTOR

    A01DRNUE05
    Text in Illustration
    *a

    Component without harness connected

    (Tilt Motor)

    1. Apply 12 V battery voltage to the tilt motor connector. Then check the steering wheel tilt operation.

      OK
      Measurement Condition Specified Condition

      12 V battery positive (+) lead → Terminal 1 (TIM+)

      12 V battery negative (-) lead → Terminal 2 (TIM-)

      		 The steering wheel tilts up.

      12 V battery positive (+) lead → Terminal 2 (TIM-)

      12 V battery negative (-) lead → Terminal 1 (TIM+)

      		 The steering wheel tilts down.

    NG

    REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) Click here

    OK

    REPLACE MULTIPLEX TILT AND TELESCOPIC ECU Click here

  6. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - TILT POSITION SENSOR)


    1. Disconnect the G116 multiplex tilt and telescopic ECU connector.

    2. Disconnect the G122 tilt motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G116-6 (VCI) - G122-4 (VCI) Always Below 1 Ω
      G116-7 (TIS) - G122-5 (TIS)
      G116-17 (E1) - G122-6 (E1)
      G116-6 (VCI) - Body ground Always 10 kΩ or higher
      G116-7 (TIS) - Body ground
      G116-17 (E1) - Body ground

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - BODY GROUND)


    1. A01DO8OE15
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Multiplex Tilt and Telescopic ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G116-11 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VCI TERMINAL VOLTAGE)


    1. A01DSO2E20
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Tilt Motor)

      Reconnect the G116 multiplex tilt and telescopic ECU connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G122-4 (VCI) - G122-6 (E1) Engine switch on (IG) 8 to 14 V

    NG

    REPLACE MULTIPLEX TILT AND TELESCOPIC ECU Click here

    OK

  9. CHECK TILT POSITION SENSOR


    1. A01DP3BE13
      Text in Illustration
      *a

      Component with harness connected

      (Multiplex Tilt and Telescopic ECU)

      Reconnect the G122 tilt motor connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G116-7 (TIS) - G116-17 (E1) Steering tilting up or tilting down

      Pulse generation

      High: 8 to 14 V

      Low: Below 1 V

    NG

    REPLACE STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR) Click here

    OK

    REPLACE MULTIPLEX TILT AND TELESCOPIC ECU Click here