DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn ON the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light/ ON or OFF | OFF | - |
| Brake Warning Light | Brake warning light/ ON or OFF | OFF | - |
| Downhill Assist Control Light | Downhill assist control indicator light/ ON or OFF | ON: Indicator light on OFF: Indicator light off |
- |
| Buzzer | Buzzer/ ON or OFF | ON: Buzzer on OFF: Buzzer off |
The combination meter has a built-in buzzer. |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied OFF: Parking brake released |
- |
| Reservoir Warning SW | Brake fluid level warning switch/ ON or OFF | OFF | - |
| Main Idle SW | Main idle switch/ ON or OFF | ON: Accelerator pedal released OFF: Accelerator pedal depressed |
- |
| Gear Position | Gear position/ Fail, 1st-8th, "P,N", R, Not R | Actual gear position | - |
| Shift Lever Position | Shift lever position/ Fail, 1st-6th/B, D/M, "P,N", R | Actual shift lever position | - |
| Shift Information | Shift information/ ON or OFF | ON: During gear change OFF: Not during gear change |
- |
| Inspection Mode | Inspection mode/ Other or Inspect | Other: Normal mode Inspect: Inspection mode |
- |
| Number of IG ON(Inspection) | Number of times ignition switch turned to ON after entering inspection mode/ Min.: 0, Max.: 255 | - | - |
| Downhill Assist Control SW | Downhill assist control switch/ ON or OFF | ON: Downhill assist control on OFF: Downhill assist control off |
- |
| Pre Crash Brake OFF Switch*1 | Pre-crash brake cancel switch/ ON or OFF | ON: Pre-crash brake cancel switch on OFF: Pre-crash brake cancel switch off |
- |
| Master Cylinder Sensor | Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V | When brake pedal released: 0.3 to 0.9 V | The value increases when the brake pedal is depressed. |
| Zero Point of M/C | Memorized zero value/ Min.: -12.50 MPa, Max.: 12.40 Mpa | - | - |
| Accumulator Sensor | Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V | 3.58 to 5.00 V | If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected. |
| Deceleration Sensor | Acceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| Zero Point of Decele | Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
| Deceleration Sensor2 | Acceleration sensor 2 reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| Zero Point of Decele2 | Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | - |
| Yaw Rate Sensor | Yaw rate sensor 1/ Min.: -128°/s, Max.: 127°/s | Vehicle stationary: 0°/s Right turn: -128 to 0°/s Left turn: 0 to 127°/s |
- |
| Zero Point of Yaw Rate | Memorized zero value/ Min.: -128°, Max.: 127° | - | - |
| Zero Point of Yaw Rate2 | Memorized zero value/ Min.: -128°/s, Max.: 127°/s | - | - |
| Steering Angle Sensor | Steering angle sensor/ Min.: -3276.8°, Max.: 3276.7° | Left turn: Increases Right turn: Decreases |
- |
| Zero Point of Steering Angle | Memorized zero value/ Min.: -3276.8°, Max.: 3276.7° | - | - |
| Lateral G | Lateral G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | Changes in proportion with acceleration during turning. |
| Forward and Rearward G | Forward and rearward G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | Changes in proportion with acceleration during acceleration/deceleration. |
| Yaw Rate Value | Yaw rate value/ Min.: -128°/s, Max.: 127°/s | - | Changes in proportion with yaw during turning. |
| Steering Angle Value | Steering angle value/ Min.: -3276.8°, Max.: 3276.7° | - | Changes in proportion with the amount of steering wheel rotation during steering operation. |
| Stop Light Relay | Stop light control ECU / ON or OFF | ON: Stop light control ECU on OFF: Stop light control ECU off |
- |
| Crawl Control Light | Crawl indicator light/ ON or OFF | ON: Indicator light on OFF: Indicator light off |
- |
| Slip Indicator Light | Slip indicator light/ ON or OFF | ON: Indicator light on OFF: Indicator light off |
- |
| Rear Diff Lock Switch | Rear differential lock detection switch/ ON or OFF | ON: Rear differential lock detection switch on OFF: Rear differential lock detection switch off |
- |
| L4 Switch | Transfer L4 detection switch/ ON or OFF | ON: L4 OFF: except L4 |
- |
| FR Wheel Speed | Front wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RR Wheel Speed | Rear wheel speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear wheel speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| Vehicle Speed | Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual vehicle speed | No large fluctuations when driving at a constant speed. |
| FR Wheel Acceleration | Front wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| FL Wheel Acceleration | Front wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| RR Wheel Acceleration | Rear wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| RL Wheel Acceleration | Rear wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| FR Wheel Direction | Front wheel direction RH/ Forward or Back | Forward: Forward Back: Back |
- |
| FL Wheel Direction | Front wheel direction LH/ Forward or Back | Forward: Forward Back: Back |
- |
| RR Wheel Direction | Rear wheel direction RH/ Forward or Back | Forward: Forward Back: Back |
- |
| RL Wheel Direction | Rear wheel direction LH/ Forward or Back | Forward: Forward Back: Back |
- |
| Stop Switch History*1 | Stop light switch history/ OFF, ON, WITHOUT or UNKNOWN | - | - |
| Stop Light Relay Output | Stop light control ECU output/ ON or OFF | ON: Stop light control ECU on (Stop light on) OFF: Stop light control ECU off (Stop light off) |
- |
| EBS Relay | Stop light control ECU (Emergency brake signal)/ ON or OFF | ON: Stop light control ECU on OFF: Stop light control ECU off |
- |
| Crawl Control Switch | Crawl speed selector switch status/ LOW, MIDLOW, MID, MIDHIGH or HIGH | Actual crawl speed selector switch position | - |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| RR Wheel EBD Ctrl Status | Rear wheel RH EBD control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| RL Wheel EBD Ctrl Status | Rear wheel LH EBD control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| BA Ctrl Status | BA control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| PBA Ctrl Status*1 | Pre-crash brake assist control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| TRC(TRAC) Ctrl Status | Traction control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| TRC(TRAC) Engine Ctrl Status | Traction control (engine control) status/ ON or OFF | ON: During control OFF: Not during control |
- |
| TRC(TRAC) Brake Ctrl Status | Traction control (brake control) status/ ON or OFF | ON: During control OFF: Not during control |
- |
| FR Wheel VSC Ctrl Status | Front wheel RH VSC control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| FL Wheel VSC Ctrl Status | Front wheel LH VSC control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| RR Wheel VSC Ctrl Status | Rear wheel RH VSC control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| RL Wheel VSC Ctrl Status | Rear wheel LH VSC control status/ ON or OFF | ON: During control OFF: Not during control |
- |
| Engine Revolutions | Engine speed/ Min.: 0 rpm, Max.: 65535 rpm | Actual engine speed | - |
| Real Engine Torque | Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm | - | - |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle/ Min.: 0.0%, Max.: 128.0% | When accelerator pedal released: 0% | Changes in proportion with the movement of the pedal during accelerator pedal operation. |
| Solenoid Relay | Solenoid relay/ ON or OFF | ON: Solenoid relay on OFF: Solenoid relay off |
- |
| ECB*2 Motor Relay | Motor relay/ ON or OFF | ON: Motor relay on OFF: Motor relay off |
- |
| TR(A)C/VSC Solenoid (SRM2) | TRC/VSC solenoid (SRM2)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| TR(A)C/VSC Solenoid (SRM1) | TRC/VSC solenoid (SRM1)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| TR(A)C/VSC Solenoid (SRC2) | TRC/VSC solenoid (SRC2)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| TR(A)C/VSC Solenoid (SRC1) | TRC/VSC solenoid (SRC1)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SFRH) | ABS solenoid (SFRH)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SFRR) | ABS solenoid (SFRR)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SFLH) | ABS solenoid (SFLH)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SFLR) | ABS solenoid (SFLR)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SRRH) | ABS solenoid (SRRH)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SRRR) | ABS solenoid (SRRR)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SRLH) | ABS solenoid (SRLH)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| ABS Solenoid (SRLR) | ABS solenoid (SRLR)/ ON or OFF | ON: Operating OFF: Not operating |
- |
| FR Speed Open | Front speed sensor RH open circuit detection/ Error or Normal | Normal | - |
| FL Speed Open | Front speed sensor LH open circuit detection/ Error or Normal | Normal | - |
| RR Speed Open | Rear speed sensor RH open circuit detection/ Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open circuit detection/ Error or Normal | Normal | - |
| EFI Communication Open | ECM communication open circuit detection/ Error or Normal | Normal | - |
| Yaw Rate Open | Yaw rate and acceleration sensor open circuit detection/ Error or Normal | Normal | - |
| Deceleration Open | Deceleration sensor open circuit detection/ Error or Normal | Normal | - |
| Steering Open | Steering angle sensor open circuit detection/ Error or Normal | Normal | - |
| Master Cylinder Open | Master cylinder pressure sensor open circuit detection/ Error or Normal | Normal | - |
| IG1 Voltage Value | IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V | Ignition switch ON: 11 to 14 V | - |
| IG2 Voltage Value | IG2 voltage value/ Min.: 0.00 V, Max.: 20.00 V | Ignition switch ON: 11 to 14 V | - |
| TRC/VSC Off Mode | TRC/VSC off mode/ Normal, TRC OFF, Unknown or VSC OFF | Normal: Normal TRC OFF: TRC OFF mode VSC OFF: VSC OFF mode |
- |
| Number of DTC | Number of DTCs/ Min.: 0, Max.: 255 | 0 | - |
| IG Voltage Value Decreased | IG1 voltage value decreased/ Error or Normal | Normal | - |
| IG Voltage Value Increased | IG1 voltage value increased/ Error or Normal | Normal | - |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open circuit detection/ Error or Normal | Normal | - |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open circuit detection/ Error or Normal | Normal | - |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open circuit detection/ Error or Normal | Normal | - |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open circuit detection/ Error or Normal | Normal | - |
| M/C Pressure Sensor Noise | Master cylinder pressure sensor noise detection/ Error or Normal | Normal | - |
| Yaw Rate Sensor Voltage Open | Yaw rate and acceleration sensor voltage open circuit detection/ Error or Normal | Normal | - |
| EFI Communication Invalid | ECM communication invalid detection/ Error or Normal | Normal | - |
| Hazard Switch History | Hazard warning switch history/ Incomplete or Complete | - | - |
| DSS Signal Buzzer*1 | Skid control buzzer/ ON or OFF | ON: Buzzer on OFF: Buzzer off |
- |
*1: w/ Dynamic Radar Cruise Control System
*2: Electronically Controlled Brake
Enter the following menus: Body Electrical / D-SEAT SW / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG | Power source input status/ ON or OFF | ON: Power source input OFF: Power source not input |
- |
| Off-road Guidance Switch | Multi-terrain select switch/ ON or OFF | ON: Switch on OFF: Switch off |
- |
| Crawl Control Main Switch | Crawl on/off switch/ ON or OFF | ON: Switch on OFF: Switch off |
- |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | Driving at constant speed: No large fluctuations |
| Dial Switch Signal 1 | Crawl speed selector/Multi-terrain select road mode selector signal 1/ ON or OFF | Switches between ON and OFF according to the ON/OFF Combination Chart Click here |
- |
| Dial Switch Signal 2 | Crawl speed selector/Multi-terrain select road mode selector signal 2/ ON or OFF | - | |
| Dial Switch Signal 3 | Crawl speed selector/Multi-terrain select road mode selector signal 3/ ON or OFF | - | |
| +B terminal voltage | +B terminal voltage/ Min.: 0.0 V, Max.: 25.5 V | 11 to 14 V | - |
| Number of Trouble Codes | Number of DTCs/ Min.: 0, Max.: 255 | 0 | - |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn ON the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON/OFF | Observe the combination meter. |
| Brake Warning Light | Brake warning light | Warning light ON/OFF | Observe the combination meter. |
| Downhill Assist Control Light | Downhill assist control indicator light | Indicator light ON/OFF | Observe the combination meter. |
| Buzzer | Buzzer | Buzzer ON/OFF | The buzzer can be heard. |
| Solenoid Relay | Solenoid relay | Relay ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| Motor Relay | Motor relay | Relay ON/OFF | An operating sound of the solenoid of the motor can be heard. |
| Stop Light Relay | Stop light control ECU | ECU ON/OFF | Observe the stop light (does not come on for 2 to 5 seconds). |
| ABS Solenoid (SRLR) | ABS solenoid (SRLR) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SRLH) | ABS solenoid (SRLH) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SRRR) | ABS solenoid (SRRR) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SRRH) | ABS solenoid (SRRH) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFLR) | ABS solenoid (SFLR) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFLH) | ABS solenoid (SFLH) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFRR) | ABS solenoid (SFRR) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFRH) | ABS solenoid (SFRH) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRMR) | VSC/TRC solenoid (SRM2) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRMF) | VSC/TRC solenoid (SRM1) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRCR) | VSC/TRC solenoid (SRC2) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRCF) | VSC/TRC solenoid (SRC1) | Solenoid ON/OFF | An operating sound of the solenoid (clicking sound) can be heard. |
| Crawl Control Light | Crawl indicator light | Indicator light ON/OFF | Observe the combination meter. |
| TRC(TRAC) OFF Indicator Light | TRC OFF indicator light | Indicator light ON/OFF | Observe the combination meter. |
| VSC OFF Indicator Light | VSC OFF indicator light | Indicator light ON/OFF | Observe the combination meter. |
| Slip Indicator Light | Slip indicator light | Indicator light ON/OFF | Observe the combination meter. |
| EBS Relay | Stop light control ECU (Emergency brake signal) | Stop light control ECU assembly ON/OFF | Make sure the hazard warning switch is off and the stop light switch is on when performing this Active Test. |
| ABS Solenoid | Selection of multiple ABS solenoids (SFRH, SFLH, SRRH, SRLH, SFRR, SFLR, SRRR and SRLR) possible | Start/Stop | Start: When Start is selected, the selected solenoids turn ON. Stop: When Stop is selected, the selected solenoids turn OFF. |
| VSC/TRC(TRAC) Solenoid | Selection of multiple VSC/TRC solenoids [SRMR (SRM2), SRMF (SRM1), SRCR (SRC2) and SRCF (SRC1)] possible | Start/Stop | Start: When Start is selected, the selected solenoids turn ON. Stop: When Stop is selected, the selected solenoids turn OFF. |
| DSS Signal Buzzer* | Skid control buzzer assembly | Buzzer ON/OFF | The buzzer can be heard. |
*: w/ Dynamic Radar Cruise Control System