ANTI-LOCK BRAKE SYSTEM DTC CHECK / CLEAR

DTC CHECK/CLEAR (When Using Intelligent Tester)

1. Check for DTCs.

   
   

   1. Turn the ignition switch off.

   2. Connect the intelligent tester to the DLC3.

   3. Turn the ignition switch to ON.

   4. Turn the intelligent tester on.

   5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

   6. Check the details of the DTCs Click here.

      Tech Tips

      Refer to the intelligent tester operator's manual for further details.

2. Clear the DTCs.

   
   

   1. Turn the ignition switch off.

   2. Connect the intelligent tester to the DLC3.

   3. Turn the ignition switch to ON.

   4. Turn the intelligent tester on.

   5. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

   6. Clear the DTCs by following the prompts on the intelligent tester.

      Tech Tips

      Refer to the intelligent tester operator's manual for further details.

DTC CHECK/CLEAR (When Using SST Check Wire)

1. 

   Text in Illustration

   *a	Front view of DLC3

   Check for DTCs.

   
   

   1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST

      09843-18040

   2. Turn the ignition switch to ON.

   3. Read the DTCs output from the ABS warning light in the combination meter.

      Tech Tips

      
      

      • When the system is normal, the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

      • When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.

      • When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and the output of all codes repeats after an interval of 4 seconds.

      • If no code is output, inspect the TC and CG terminal circuit and ABS warning light circuit.

      Trouble Area	See Procedure
      TC and CG terminal circuit	Click here
      ABS warning light circuit (Remains on)	Click here
      ABS warning light circuit (Does not come on)	Click here

   4. Codes are explained in the DTC chart.

      ABS DTC

      ABS Warning Light Display	Intelligent Tester Display
      11	C0278
      12	C0279
      13	C0273
      14	C0274
      21	C0226
      22	C0236
      23	C0246
      24	C0256
      25	C1225
      31	C1401
      	C1405
      	C1409
      32	C1402
      	C1406
      	C1410
      33	C1403
      	C1407
      	C1411
      34	C1404
      	C1408
      	C1412
      35	C1413
      36	C1414
      37	C1337
      38	C1415
      39	C1416
      41	C1241
      	C1417
      43	C1243
      44	C1419
      	C1420
      	C1442
      45	C1245
      46	C1421
      	C1422
      	C1423
      	C1424
      49	C1425
      	C1426
      51	C1427
      	C1428
      59	C1203
      67	C1429
      	C1430
      	C1431
      68	C1268
      91	C1361
      94	U0073
      95	U0124
      97	C1381
      A1*	U0114

      
      

      • *: The light blinks 10 times, turns off for 1.5 seconds, and then blinks once.

   5. Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.

      Tech Tips

      If 2 or more DTCs are output at the same time, the DTCs are output in ascending order.

2. Clear the DTCs.

   
   
   1. 

      Text in Illustration

      *a	Front view of DLC3

      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST

      09843-18040

   2. Turn the ignition switch to ON.

   3. Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.

   4. Check that the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

   5. Remove SST from the terminals of the DLC3.

END OF DTC CHECK/CLEAR

1. Turn the ignition switch to ON.

2. Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch to ON.