AIR SUSPENSION SYSTEM, Diagnostic DTC:C1751/51

DTC Code DTC Name
C1751/51 Compressor Relay Coil Malfunction

DESCRIPTION

When the "up" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to the AIR SUS relay to turn the relay on.

As a result, the current flows to the AIR SUS relay coil, closing the relay contact, and then battery positive voltage is applied to the height control compressor, which causes compressed air to raise the vehicle height.

DTC Code DTC Detection Condition Trouble Area
C1751/51

Either condition is met:


  • With the AIR SUS relay inactivated, an open signal of the AIR SUS relay is detected for 1 second or more.

  • With the AIR SUS relay activated, a short signal of the AIR SUS relay is detected 8 times successively.

  • Harness or connector

  • AIR SUS relay (Suspension control relay)

  • Suspension control ECU

Tech Tips

Once the suspension control ECU stores DTC C1751/51 in memory, vehicle height control is suspended until a normal signal is input to the suspension control ECU from the AIR SUS relay. However, control is resumed if the ignition switch is turned off and then to ON again.

WIRING DIAGRAM

A01DTSVE01

INSPECTION PROCEDURE

Note

When replacing the suspension control ECU, perform registration Click here.

Tech Tips

If DTC C1782/82 is output at the same time as C1751/51, perform the inspection necessary for DTC C1782/82 first Click here.

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (COMPRESSOR MOTOR RELAY)


    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / Air suspension / Active Test.

      Air Suspension
      Tester Display Test Part Control Range Diagnostic Note
      Compressor Motor Relay AIR SUS relay ON or OFF

      • The operating sound of the motor can be heard.

      • When the Active Test is performed, Motor Relay in the Data List changes between ON and OFF accordingly.
      OK
      Operation of motor can be heard.
      Result
      Result Proceed to
      NG A
      OK (When troubleshooting according to problem symptoms table) B
      OK (When troubleshooting according to DTC chart) C

    B

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. INSPECT SUSPENSION CONTROL RELAY (AIR SUS)


    1. Turn the ignition switch off.

    2. Remove the AIR SUS relay from the engine room relay block.

    3. A01DNMJE14
      Text in Illustration
      *1 AIR SUS Relay

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 12 V battery voltage is not applied to terminal 1 and 2 10 kΩ or higher
      12 V battery voltage is applied to terminal 1 and 2 Below 1 Ω

    NG

    REPLACE SUSPENSION CONTROL RELAY (AIR SUS)

    OK

  3. CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - AIR SUS RELAY)


    1. Disconnect the R19 suspension control ECU connector.

    2. Remove the AIR SUS relay from the engine room relay block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R19-22 (RC) - Engine room relay block AIR SUS relay terminal 1 Always Below 1 Ω
      R19-22 (RC) - Body ground Always 10 kΩ or higher
      Engine room relay block AIR SUS relay terminal 2 - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE SUSPENSION CONTROL ECU Click here