KINETIC DYNAMIC SUSPENSION SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn ON the intelligent tester.

    5. Enter the following menus: Chassis / KDSS / Data List.

    6. According to the display on the intelligent tester, read the Data List.

      KDSS
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Oil Pressure Sensor

      Oil pressure sensor/

      Min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)

      Max.: 784.76 MPa (8002.35 kgf/cm2, 113790.20 psi)

      2.6 MPa (26.5 kgf/cm2, 377 psi) to 3.0 MPa (30.6 kgf/cm2, 435 psi): When vehicle stopped and fluid temperature 20°C (68°F)

      		 -
      Acceleration Sensor

      Lateral G/

      Min.: -1176.37 m/s2

      Max.: -1176.33 m/s2

      		- Changes in proportion with acceleration during turning.
      Stop Light Switch

      Stop light switch/

      ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      		 -
      TC Terminal

      TC terminal/

      ON or OFF

      		 OFF -
      TS Terminal

      TS terminal/

      ON or OFF

      		 OFF -
      FR Wheel Speed

      Front wheel RH speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      		 Actual wheel speed No large fluctuations when driving at a constant speed.
      FL Wheel Speed

      Front wheel LH speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      		 Actual wheel speed No large fluctuations when driving at a constant speed.
      RR Wheel Speed

      Rear wheel RH speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      		 Actual wheel speed No large fluctuations when driving at a constant speed.
      RL Wheel Speed

      Rear wheel LH speed/

      Min.: 0 km/h (0 mph)

      Max.: 255 km/h (158 mph)

      		 Actual wheel speed No large fluctuations when driving at a constant speed.
      IG Power Source Voltage

      IG power source voltage/

      Min.: 0.0 V

      Max.: 25.5 V

      		 Ignition switch ON: 11 to 14 V -
      Steering Angle

      Steering angle/

      Min.: -49152.0 deg

      Max.: 49150.5 deg

      		 - Changes in proportion with the amount of steering wheel rotation during steering operation.
      Compatible Constant Information

      Compatible constant information/

      Min.: 0

      Max.: 255

      		 - -
      Design Constant Information

      Design constant information/

      Min.: 0

      Max.: 255

      		 - -
      Accumulator Valve (Downside)

      Stabilizer control solenoid valve (for Lower Chamber)/

      ON or OFF

      ON: Stabilizer control solenoid valve closed

      OFF: Stabilizer control solenoid valve open

      		 -
      Accumulator Valve (Upside)

      Stabilizer control solenoid valve (for Upper Chamber)/

      ON or OFF

      ON: Stabilizer control solenoid valve open

      OFF: Stabilizer control solenoid valve closed

      		 -
      Number of Trouble Codes

      Number of trouble codes/

      Min.: 0

      Max.: 255

      		 0 -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Warm up the engine.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn ON the intelligent tester.

    5. Enter the following menus: Chassis / KDSS / Active Test.

    6. According to the display on the intelligent tester, perform the Active Test.

      KDSS
      Tester Display Test Part Control Range Diagnostic Note
      Accumulator Valve (Upside) Stabilizer control solenoid valve (for Upper Chamber) Valve ON / OFF

      The operating sound of the solenoid (clicking sound) can be heard

      ON: Data List ON

      OFF: Data List OFF

      When the Active Test is performed, the solenoid turns on for 3 seconds.
      Accumulator Valve (Downside) Stabilizer control solenoid valve (for Lower Chamber) Valve ON / OFF

      The Operating sound of the solenoid (clicking sound) can be heard

      ON: Data List ON

      OFF: Data List OFF

      When the Active Test is performed, the solenoid turns on for 3 seconds.