Click here

AUTOMATIC TRANSMISSION SYSTEM (for 1KD-FTV), Diagnostic DTC:P0717

Click here
Click here Click here
DTC Code DTC Name
P0717 Turbine Speed Sensor Circuit No Signal
Click here

DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transmission. By comparing the input turbine speed signal NT with the counter gear speed sensor signal SP2, the TCM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions. As a result, the gears shift smoothly.

DTC Code DTC Detection Condition Trouble Area
P0717

All conditions are met for 5 sec. or more (1- trip detection logic):

(a) Gear shift is not being performed.

(b) Transmission is in 4th or 5th gear.

(c) Transmission input shaft speed is 300 rpm or less.

(d) Transmission output shaft speed is 1000 rpm or more.

(e) Park/neutral position switch R input signal is OFF.

(f) Shift solenoid valves and park/neutral position switch are normal.

  • Open or short in speed sensor NT circuit

  • Speed sensor NT

  • TCM

  • Automatic transmission (clutch, brake, gear, etc.)

Reference: Inspect using an oscilloscope.

Check the waveform of the TCM connector.

Standard
Terminal No. (Symbol) Tool Setting Condition Specified Condition
G69-3 (NT+) - G69-2 (NT-) 1 V/DIV., 2 msec./ DIV. Engine idling (shift lever in P or N) Refer to illustration
Click here

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NT (turbine (input) speed sensor) or is output only a little. The NT terminal of the TCM detects the pulse signal from the speed sensor NT (input turbine speed). The TCM outputs a gear shift signal by comparing the input speed sensor NT signal with the output speed sensor SP2.

While the vehicle is operating in 4th or 5th gear with the shift lever in D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is 1000 rpm or more*2, the TCM detects the trouble, illuminates the MIL and stores the DTC.

Tip:

  • *1: A pulse is not output or is irregularly output.

  • *2: The vehicle speed is approximately 50 km/h (31 mph) or more.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE


Click here

  1. DATA LIST

    Tip:

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note:

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the intelligent tester on.

    6. Enter the following menus: Powertrain / ECT / Data List.

    7. According to the display on the intelligent tester, read the Data List.

    Table 1. ECT
    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    SPD (NT)

    Input shaft speed/

    Min.: 0 rpm

    Max.: 12750 rpm

    • Lock-up ON (after warming up engine): Input turbine speed (NT) equal to engine speed

    • Lock-up OFF (idling with shift lever in N): Input turbine speed (NT) nearly equal to engine speed

    		 Data is displayed in increments of 50 rpm.
    Tip:

    • SPD (NT) is always 0 while driving:

      Open or short in the sensor or circuit.

    • SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:

      Sensor trouble, improper installation or intermittent connection trouble in the circuit.

Click here

PROCEDURE


  1. Click here

    INSPECT SPEED SENSOR NT INSTALLATION


    1. A01DU4QE01

      Check the speed sensor NT installation.

      OK
      The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
      Table 2. Text in Illustration
      *a CORRECT
      *b INCORRECT

  2. Click here

    INSPECT SPEED SENSOR NT


    1. A01DUIZE05

      Disconnect the C32 speed sensor connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 560 to 680 Ω
      Table 3. Text in Illustration
      *a

      Component without harness connected

      (Speed Sensor NT)

  3. Click here

    CHECK HARNESS AND CONNECTOR (SPEED SENSOR NT - TCM)


    1. A01DQ7JE02

      Disconnect the G69 TCM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G69-3 (NT+) - G69-2 (NT-) 20°C (68°F) 560 to 680 Ω
      G69-3 (NT+) - Body ground Always 10 kΩ or higher
      G69-2 (NT-) - Body ground Always 10 kΩ or higher
      Table 4. Text in Illustration
      *a

      Rear view of wire harness connector

      (to TCM)

  4. Click here

    SECURELY INSTALL OR REPLACE SPEED SENSOR NTClick here

  5. Click here

    REPLACE SPEED SENSOR NTClick here

  6. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. Click here

    REPLACE TCMClick here