INTAKE MANIFOLD (w/ DPF) REMOVAL

Note


  • When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note


    • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

    Click here

  3. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

    Click here

  4. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR


    1. A01DUFS

      Disconnect the manifold absolute pressure sensor connector and vacuum hose.

    2. Remove the bolt and manifold absolute pressure sensor.

  5. REMOVE EMISSION CONTROL VALVE BRACKET


    1. A01DQAM

      Remove the bolt and emission control valve bracket.

  6. REMOVE THROTTLE BODY BRACKET


    1. A01DPGW

      Remove the 3 bolts and throttle body bracket.

  7. REMOVE NO. 1 GAS FILTER


    1. A01DP2T

      Disconnect the vacuum hose and remove the No. 1 gas filter from the gas filter bracket.

  8. REMOVE GAS FILTER BRACKET


    1. A01DMQK

      Detach the clamp and disconnect the wire harness.

    2. A01DSGE

      Remove the bolt and gas filter bracket.

  9. DISCONNECT WIRE HARNESS


    1. A01DU9L

      Remove the bolt and disconnect the wire harness.

    2. A01DOMZ

      for LHD:

      Remove the bolt and disconnect the wire harness.

    3. Detach the 5 clamps and disconnect the wire harness from the cowl top panel.

  10. REMOVE INTAKE AIR CONNECTOR


    1. A01DSTL

      Remove the 3 bolts, intake air connector and gasket.

  11. REMOVE NO. 1 FUEL PIPE


    1. Disconnect the No. 2 fuel pipe Click here.

    2. Remove the 4 bolts, union bolt, gasket and No. 1 fuel pipe.

      A01DTAKE01
      Text in Illustration
      *1 No. 2 Fuel Pipe - -
      A01DMKT Union Bolt - -

  12. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY


    1. A01DSLU

      Remove the bolt, nut and 2 No. 2 injection pipe clamps.

    2. A01DP3CE01
      Text in Illustration
      *a Common Rail Assembly Side
      *b Injector Assembly Side

      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe sub-assembly.

  13. REMOVE NO. 2 FUEL PIPE


    1. A01DTYW

      Using a 6 mm hexagon wrench, remove the union bolt and gasket.

      Text in Illustration
      A01DQPB Union Bolt
      A01DMKT Fuel Check Valve
      A01DPHJ Bolt

    2. Remove the fuel check valve and gasket.

    3. Remove the bolt and No. 2 fuel pipe.

  14. REMOVE NO. 3 NOZZLE LEAKAGE PIPE


    1. A01DPHI

      Disconnect the 2 fuel hoses.

      Text in Illustration
      A01DMKT Fuel Check Valve

    2. Remove the 2 bolts.

    3. Remove the fuel check valve, gasket and No. 3 nozzle leakage pipe.

  15. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY


    1. A01DS6P

      Remove the 2 bolts.

      Text in Illustration
      A01DMKT Union Bolt

    2. Remove the union bolt, gasket and No. 2 nozzle leakage pipe assembly.

  16. REMOVE INTAKE PIPE STAY


    1. A01DRKX

      Remove the bolt and intake pipe stay.

  17. REMOVE VACUUM CONTROL VALVE SET


    1. Disconnect the 2 vacuum switching valve connectors.

    2. A01DMFA

      Disconnect the 3 vacuum hoses, and then remove the 2 bolts and vacuum control valve set.

  18. REMOVE NO. 2 MANIFOLD STAY


    1. A01DUBL

      Remove the bolt and No. 2 manifold stay.

  19. REMOVE NO. 1 GLOW PLUG CONNECTOR


    1. Disconnect the No. 1 glow plug connector from the wire harness.

    2. A01DPSG

      Remove the 4 screw grommets.

    3. A01DNFC

      Remove the 4 nuts and No. 1 glow plug connector.

  20. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR

    A01DMQU

  21. REMOVE INTAKE MANIFOLD INSULATOR


    1. A01DPSM

      Remove the intake manifold insulator.

  22. REMOVE INTAKE MANIFOLD


    1. A01DP4B

      Detach the sensor wire connector clamp from the intake manifold.

    2. A01DPG9

      Remove the 2 nuts, 4 bolts, intake manifold and gasket.