SIDE MONITOR SYSTEM, Diagnostic DTC:C1683, C1684

DTC Code DTC Name
C1683 Side Camera Feedback Malfunction
C1684 Side Camera Current Malfunction

DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.

DTC Code DTC Detection Condition Trouble Area
C1683 Side Camera Feedback Malfunction

  • Harness or connector

  • Parking assist ECU

  • Front passenger side television camera assembly

  • Front passenger side outer rear view mirror assembly
C1684 Side Camera Current Malfunction

  • Harness or connector

  • Parking assist ECU

  • Front passenger side television camera assembly

  • Front passenger side outer rear view mirror assembly

WIRING DIAGRAM

A01DSJUE03

INSPECTION PROCEDURE

Note

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed Click here.

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1683 and C1684 are not output A
      DTC C1683 and/or C1684 is output B

    B

    CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY) Click here

    A

    USE SIMULATION METHOD TO CHECK Click here

  2. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY)


    1. Disconnect the I7 parking assist ECU connector.

    2. Disconnect the J3*1 or K2*2 front passenger side outer rear view mirror assembly connector.


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      I7-34 (SCV-) - J3-12 (SCV-) Always Below 1 Ω
      I7-10 (SCV+) - J3-6 (SCV+) Always Below 1 Ω
      I7-33 (SGND) - J3-13 (SGND) Always Below 1 Ω
      I7-32 (SCB+) - J3-5 (SCB+) Always Below 1 Ω
      I7-34 (SCV-) - Body ground Always 10 kΩ or higher
      I7-10 (SCV+) - Body ground Always 10 kΩ or higher
      I7-33 (SGND) - Body ground Always 10 kΩ or higher
      I7-32 (SCB+) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      I7-34 (SCV-) - K2-12 (SCV-) Always Below 1 Ω
      I7-10 (SCV+) - K2-6 (SCV+) Always Below 1 Ω
      I7-33 (SGND) - K2-13 (SGND) Always Below 1 Ω
      I7-32 (SCB+) - K2-5 (SCB+) Always Below 1 Ω
      I7-34 (SCV-) - Body ground Always 10 kΩ or higher
      I7-10 (SCV+) - Body ground Always 10 kΩ or higher
      I7-33 (SGND) - Body ground Always 10 kΩ or higher
      I7-32 (SCB+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK PARKING ASSIST ECU


    1. A01DU6EE31
      Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I7-33 (SGND) - Body ground Always Below 1 Ω

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I7-32 (SCB+) - I7-33 (SGND) Engine switch on (IG), wide view front and side monitor switch on 5.5 to 7.05 V
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    REPLACE PARKING ASSIST ECU Click here

    C

    REPLACE PARKING ASSIST ECU Click here

    A

  4. CHECK FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY


    1. Measure the waveform of the front passenger side television camera assembly using an oscilloscope.

      A01DS32E30
      Text in Illustration
      *a

      Component with harness connected

      (Parking Assist ECU)

      		 *b Waveform A
      *c Waveform B *d Synchronized Signal
      *e Video Waveform - -

      Tech Tips


      • A waterproof connector is used for the side television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.


        • *1: for Navigation Receiver Type

        • *2: for Radio and Display Type

      • The video waveform changes according to the image sent by the side television camera assembly.

      Measurement Condition
      Item Content
      Tester Connection I7-10 (SCV+) - I7-33 (SGND)
      Tool Setting 200 mV/DIV., 50 μsec./DIV.
      Condition

      • Waveform A: Engine switch on (IG), wide view front and side monitor switch on, camera lens not covered, displaying image

      • Waveform B: Engine switch on (IG), wide view front and side monitor switch on, camera lens covered, blacking out screen
      OK
      Waveform is as shown in illustration.
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    B

    REPLACE PARKING ASSIST ECU Click here

    C

    REPLACE FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY Click here

    A

    REPLACE PARKING ASSIST ECU Click here

  5. REPLACE FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY


    1. Replace the front passenger side television camera assembly with a new or normally functioning one Click here.


    NEXT

  6. CHECK FOR DTC


    1. Clear the DTCs Click here.

    2. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC C1683 and C1684 are not output A
      DTC C1683 and/or C1684 is output B

    B

    REPLACE FRONT PASSENGER SIDE OUTER REAR VIEW MIRROR ASSEMBLY Click here

    A

    END (FRONT PASSENGER SIDE TELEVISION CAMERA ASSEMBLY IS DEFECTIVE)