Click here

NAVIGATION SYSTEM (for Built-in Memory) HOW TO PROCEED WITH TROUBLESHOOTING

Click here
Click here Click here
Tip:

  • Use the following procedure to troubleshoot the navigation system.

  • *: Use the GTS.


  1. Click here

    VEHICLE BROUGHT TO WORKSHOP


    • NEXT
  2. Click here

    CUSTOMER PROBLEM ANALYSIS


    • When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

    • Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

    • The following 5 items are important points in problem analysis:

      What Vehicle model, system name
      When Date, time, occurrence frequency
      Where Road conditions
      Under what conditions? Driving conditions, weather conditions
      How did it happen? Problem symptoms

    • NEXT
  3. Click here

    INSPECT BATTERY VOLTAGE


    1. Measure the battery voltage.

      Standard voltage
      11 to 14 V
      Tip:

      If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


      • NEXT
  4. Click here

    CHECK CABIN


    1. Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

      OK
      Condensation is not likely being produced and the temperature is not high or extremely low.
      Tip:

      • A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

      • The navigation system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.


      • NG
      • SET CABIN TO APPROPRIATE TEMPERATURE
      • OK
  5. Click here

    CHECK NAVIGATION SYSTEM NORMAL CONDITION


    1. Refer to Check Navigation System Normal Condition (Click here).

      Table 1. Result
      Result Proceed to
      Symptom is not normal operation. A
      Symptom is normal operation. B

      • B
      • SYMPTOM IS NORMAL OPERATION
      • A
  6. Click here

    CHECK CAN COMMUNICATION SYSTEM*


    1. Check if CAN communication system DTCs output (Click here).

      Table 2. Result
      Result Proceed to
      CAN DTCs are not output. A
      CAN DTCs are output. B

      • B
      • GO TO CAN COMMUNICATION SYSTEM (See pageClick here)
      • A
  7. Click here

    CHECK FOR DTC*


    1. Refer to DTC Check/Clear (Click here).

      Table 3. Result
      Result Proceed to
      DTCs are output. A
      DTCs are not output. B

      • B
      • Go to step 11
      • A
  8. Click here

    DTC CLEAR*


    1. Refer to DTC Check/Clear (Click here).

      Tip:

      The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.


      • NEXT
  9. Click here

    RECHECK FOR DTC*


    1. Refer to DTC Check/Clear (Click here).

      Table 4. Result
      Result Proceed to
      DTCs are output. A
      DTCs are not output. B
      Tip:

      • Even if the malfunction symptom is not confirmed, check for DTCs. This is because the system stores history DTCs.

      • Check the DTCs and inspect the area that the code indicates.


      • B
      • Go to step 11
      • A
  10. Click here

    DIAGNOSTIC TROUBLE CODE CHART


    1. Find the output code in Diagnostic Trouble Code Chart (Click here).

      Note:

      • The navigation system outputs DTCs for the following system.

      • When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.

      • Refer to Parking Assist Monitor System (w/o Side Monitor) (Click here).

      Table 5. Result
      Result Proceed to
      DTCs for the parking assist monitor system (w/o Side Monitor System) are output. A
      DTCs for the navigation system are output. B

      • B
      • Go to step 13
      • A
      • GO TO PARKING ASSIST MONITOR SYSTEM (w/o Side Monitor System) (See pageClick here)
  11. Click here

    PROBLEM SYMPTOMS TABLE


    1. Refer to Problem Symptoms Table (Click here).

      Table 6. Result
      Result Proceed to
      Fault is not listed in Problem Symptoms Table. A
      Fault is listed in Problem Symptoms Table. B
      Tip:

      If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms (Click here).


      • B
      • ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE
      • A
  12. Click here

    PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM


    1. Refer to Terminals of ECU (Click here).


      • NEXT
  13. Click here

    CHECK CIRCUIT


    1. Adjust, repair or replace as necessary.


      • NEXT
  14. Click here

    RECHECK FOR DTC


    1. After clearing DTCs, recheck for DTCs (Click here).


      • NEXT
  15. Click here

    PERFORM CONFIRMATION TEST


    • NEXT
    • END