NAVIGATION SYSTEM (for Navigation Receiver Type) OPERATION CHECK


  1. CHECK NAVIGATION SYSTEM NORMAL CONDITION


    1. If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not a malfunction.

      Symptom Answer
      A longer route than expected is chosen. Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker.
      Even when distance priority is high, the shortest route is not shown. Some routes may not be advised due to safety concerns.
      When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position. If the vehicle starts before the navigation system activates, the system may not react.
      When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position. When the vehicle is driving on new roads not available on the SD card, the system attempts to match it to another nearby road, causing the position mark to deviate.
    2. A01DM74

      The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.


      1. The current position mark may be displayed on a nearby parallel road.

      2. A01DSNL

        Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.

      3. A01DN2S

        When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.

      4. A01DRV3

        When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.

      5. A01DT2D

        When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.

      6. A01DUDZ

        When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.

      7. A01DU04

        When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.

      8. A01DU1N

        When the engine switch is turned to on (ACC or IG) and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.

      9. A01DR8A

        When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.

      10. A01DTJ9

        When the tires are changed, the current vehicle position mark may deviate from the correct position.

        Tech Tips


        • A change in tire diameter may cause a speed sensor error.

        • Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.

  2. CHECK SD CARD (except Pioneer Made)

    Tech Tips


    • Check the SD card installed into the navigation receiver assembly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DPDV

      Select "Failure Diagnosis" from the "Service Menu" screen.

    3. A01DO6V

      Select "SD Check" from the "Failure Diagnosis" screen.

    4. A01DSJIE01
      Text in Illustration
      *a Result

      SD Check


      1. Select "SD Check" to start the SD card check.

      2. Check that the result is displayed when the SD check is completed.

        Screen Description
        Display (Result) Description
        Checking Check is in progress
        OK SD card is normal
        NG SD card is malfunctioning

        Tech Tips


        • After selecting "SD Check", it may take a while until the result is displayed.

        • If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the SD card may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.

        • If "NG" is displayed even when the cabin temperature is appropriate, replace the SD card with a new one.

  3. CHECK SD CARD (for Pioneer Made)

    Tech Tips

    Check the SD card installed into the navigation receiver assembly.


    1. Check whether the navigation screen is displayed when the "HOME" switch is pressed.

    2. If the navigation screen is not displayed, a warning message is displayed, and the navigation system continues to operate in audio mode, replace the SD card as the SD card is defective.

  4. CHECK PANEL & STEERING SWITCH

    Tech Tips


    • The navigation receiver assembly panel switches and steering switches are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DQSH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01DPX2E01
      Text in Illustration
      *a Example

      Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

    4. A01DP8LE01

      Panel & Steering Switch Check Mode

      Screen Description (except Pioneer Made)
      Display Content
      *a: Switch condition "Pushed" is displayed when any switch is pushed
      *b: Number of switches pushed

      • Number of switches pushed at once is displayed

      • If more than 3 switches are pushed at once, "More than 3" is displayed

      • If 4 or more switches are pushed at once, "More than 3" is displayed
      *c: Rotary switch direction Direction of rotary switch is displayed
      Screen Description (for Pioneer Made)
      Display Content
      *a: Switch condition

      • "Pushed" is displayed when any switch is pushed

      • If 2 or more switches are pushed at once, nothing is displayed
      *b: Number of switches pushed

      • "1" is displayed when any switch is pushed

      • If 2 or more switches are pushed at once, nothing is displayed
      *c: Rotary switch direction Direction of rotary switch is displayed

      1. Operate each switch and check that the switch conditions are correctly displayed.

        Note

        When the "APPS" or "MENU" switch is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

  5. CHECK TOUCH SWITCH

    Tech Tips


    • The touch switches on the screen are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DQSH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01DPTDE01
      Text in Illustration
      *a Example

      Select "Touch Switch" from the "Function Check/Setting I" screen.

    4. Touch Switch Check


      1. A01DUTU

        Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

        Tech Tips


        • A "+" mark is displayed where the display is touched.

        • The "+" mark remains on the display even after the finger is removed.

  6. CHECK MIC & VOICE RECOGNITION

    Tech Tips


    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DQSH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01DTB5E01
      Text in Illustration
      *a Example

      Select "Microphone Check" from the "Function Check/Setting I" screen.

    4. A01DPY6E01

      Microphone Check

      Screen Description
      Display Content
      *a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
      *b: Recording switch Starts recording.
      *c: Stop switch Stops recording and playing.
      *d: Play switch Plays the recorded voice.
      *e: Recording indicator Comes on while recording.

      1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

        Tech Tips

        The microphone is active at all times when this screen is displayed.

      2. Push the recording switch and perform voice recording.

        Tech Tips


        • Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

        • While recording or playing, the switches other than the stop switch cannot be pushed.

        • When no recording is present, the play switch cannot be pushed.

        • Recording will stop after 5 seconds or when the stop switch is pushed.

      3. Check that the recording indicator remains on while recording and that the recording can be played normally.

  7. CHECK GPS & VEHICLE SENSORS

    Tech Tips


    • GPS information, vehicle signals and sensor signals are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DQSH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01DTTWE01
      Text in Illustration
      *a Example

      Select "System Sensor Check" from the "Function Check/Setting I" screen.

    4. A01DSTOE01

      System Sensor Check

      *a: GPS
      Display Content
      Reception number Displays reception condition of the satellites used to determine vehicle position Blue: P (In use) System is using GPS signal for location.
      Yellow: T (Receiving) System is tracking GPS signal for location.
      No color: Not in use System cannot receive GPS signal. (Searching for GPS signal)
      Status Displays reception status of the satellites used to determine vehicle position OK (H3D) High accuracy 3-dimensional location method is being used. (except Pioneer Made)
      OK (H2D) High accuracy 2-dimensional location method is being used. (except Pioneer Made)
      OK (3D) 3-dimensional location method is being used.
      OK (2D) 2-dimensional location method is being used.
      NG Location data cannot be used.
      error Reception error has occurred.
      - Any other state.
      Measurement ratio Displays the ratio of satellites performing measurements 3D The ratio of satellites performing 3D positioning, Hyper 3D positioning and Hyper 2D positioning is displayed.
      2D The ratio of satellites performing 2D positioning is displayed.
      NG The ratio of satellites not performing measurement is displayed.
      Date Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).
      Position Latitude and longitude information on current position is displayed.
      *b: SPD
      Display Content
      Pulse count Displays the accumulated number of input pulses beginning when this screen is displayed
      Speed Displays vehicle speed
      *c: Sensor Signal
      Display Content Note
      Gyro Voltage Displays the output voltage of the gyro sensor -
      0 point Voltage Displays the zero-point voltage of the gyro sensor -
      Relative bearing Displays the output angle of the gyro sensor The amount of change in bearing angle (degrees) after the system sensor check screen is displayed (clockwise: "+", counterclockwise: "-").
      *d: Reset
      Display Content
      Reset When this switch is pressed and held for 3 seconds or more, the values for display items of SPD signal and gyro sensor signal are reset and display "0".
      *e: Gyro/Distance correction study situation
      Display Content
      Gyro/Distance correction study situation Displays learning status of Gyro/Distance correction

      1. When the "System Sensors Check" screen is displayed, check all the sensor signals.

        Tech Tips

        This screen is updated once per second.

    5. A01DQT0E01

      GPS Time Setting

      Screen Description
      Display Content
      *a: Time display Displays the date and time in the device.
      *b: Time setting screen Setting is possible only when GPS signals are not being received.
      *c: Cursor movement switch Moves the cursor on the date and time setting screen to the right and left.
      *d: Adjustment switch Adjusts values of items selected by the cursor.
      *e: OK switch Selecting this switch after setting the date and time updates the date and time in the device (only when GPS signals are not received).

      1. When GPS signals are not being received, the data and time in the device can be adjusted.

        Tech Tips

        Time setting is possible only when GPS signals are not being received. When the navigation system is receiving GPS signals, priority is given to displaying the time and date received via GPS.

  8. CHECK VEHICLE SIGNAL

    Tech Tips


    • Vehicle signals received by the navigation receiver assembly are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DQSH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01DTB1E01
      Text in Illustration
      *a Example

      Select "Vehicle Signal" from the "Function Check/Setting I" screen.

    4. A01DUN2

      Vehicle Signal Check Mode

      Screen Description
      Display Content
      Battery Battery voltage is displayed.
      IG Engine switch ON/OFF state is displayed.
      PKB Parking brake ON/OFF state is displayed.
      REV Reverse signal ON/OFF state is displayed.
      SPEED Vehicle speed is displayed in km/h.
      TAIL Tail signal (Light control switch) ON/OFF state is displayed.
      ADIM/TCAN Brightness state DIM (with) / BRIGHT (without) is displayed.

      Tech Tips


      • Only conditions have inputs are displayed.

      • This screen displays vehicle signals input to the navigation receiver assembly.


      1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

  9. CHECK HANDS-FREE VOICE QUALITY AND VOLUME SETTING

    Note


    • Adjustment of the settings is required for each registered cellular phone.

    • If no cellular phone has been registered, all switches cannot be selected.

    Tech Tips


    • The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DQSH

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01DUHUE01
      Text in Illustration
      *a Example

      Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

    4. A01DUSTE01
      Screen Description
      *a Numeric keypad
      *b Setting button
      *c Reset button

      Hands-Free Voice Quality Setting (Voice Quality Type adjustment)


      1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

      2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

        Settings
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality

        A

        (Noise)

        		 The other party hears background noise when listening to your voice. 1000 The amount of background noise the other party hears when listening to your voice is reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        B

        (Noise)

        		 The other party hears a lot of background noise when listening to your voice. 2000 The amount of background noise the other party hears when listening to your voice is sharply reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        C

        (Echo)

        		 The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).

        D

        (Echo)

        		 The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).
        Settings (When Multiple Phenomena Occurred)
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
        A+C The other party hears background noise and weak echoes when listening to your voice. 1100

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).
        A+D The other party hears background noise and strong echoes when listening to your voice. 1200

        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).
        B+C The other party hears a lot of background noise and weak echoes when listening to your voice. 2100

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (low level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).
        B+D The other party hears a lot of background noise and strong echoes when listening to your voice. 2200

        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (high level).

        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).

        Tech Tips


        • The default value is "0000".

        • Settings will be applied when the setting button is selected.

        • If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

        • If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by pressing the "INIT" switch.

  10. CHECK DAB RECEPTION (w/ DAB Function)

    Tech Tips


    • The reception condition of Digital Audio Broadcast (DAB) can be checked.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DPIQ

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01DT9D

      Select "Next Page" from the "Function Check/ Setting I" screen.

    4. A01DS1I

      Select "DAB Reception Check" from the "Function Check/Setting II" screen.

    5. A01DS4VE03

      DAB Reception Check

      Screen Description
      Display Content
      *a: Up or down switch Enables the channel to be changed to the one to be checked.
      *b: Check/STOP switch

      • Check: Starts checking

      • STOP: Stops checking
      *c: Antenna connection check

      DAB antenna connection status as follows:


      • OK: Connected properly

      • NG: Not connected properly

      • -: Not equipped with DAB antenna.
      *d: DAB Tuner Reception Level Check Result Description

      Displays DAB antenna reception levels as follows:


      • 111 or more: Font color is black (good reception)

      • 110 or less: Font color is red (poor reception)

      • -: Not equipped with DAB antenna.

    6. Select the "Check" button to start the DAB reception check.

    7. Check the result displayed when the DAB reception check is complete.

      Tech Tips

      If the reception level is abnormal, the antenna system or navigation receiver assembly is malfunctioning.

  11. CLEAR PASSWORD OF EXPORT/IMPORT MEMORY POINT FUNCTION (w/ Export/Import Memory Point Function)

    Tech Tips


    • This function allows the initialization of a password which was set on the navigation receiver assembly when exporting/importing memory points.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode Click here.

    2. A01DP5L

      Select "Service Information" from the "Service Menu" screen.

    3. A01DQYD

      Select "Memory point backup" from the "Service Information" screen.

    4. A01DRAZ

      Clear backup password

      Tech Tips

      Depending on the manufacturer, some component names and versions will be displayed differently.


      1. Select "Clear backup password" from the "Memory point backup" screen.

  12. CHECK SPEAKER

    Tech Tips


    • This function is used when checking the speaker wiring and whether the speakers are functioning properly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Turn audio mode on and play any audio source.

      Tech Tips

      This audio source will be used for the speaker check.

    2. Enter diagnostic mode Click here.

    3. A01DURM

      Select "Failure Diagnosis" from the "Service Menu" screen.

    4. A01DQKN

      Select "System Check" from the "Failure Diagnosis" screen.

    5. A01DP6F

      Select "SP Check ON" from the "System Check Mode" screen.

    6. Check the speaker wiring and check that the speakers are functioning properly.

      Tech Tips


      • Check that each speaker outputs sound from the selected audio source properly.

      • "SP Check OFF" is displayed during the speaker check.

      • Sound can be heard from the speakers around the vehicle in order beginning from the speaker on the front side.

      • More than one speaker may sound simultaneously depending on the speaker wiring.

    7. Sound stops when any of the following conditions are met.


      1. The "SP Check OFF" switch is pressed.

      2. The engine switch is turned off.

      3. Diagnostic mode is turned off.

      4. The screen is changed to another screen.

      5. Audio mode is turned off.

  13. CHECK SOFTWARE ERROR HISTORY

    Tech Tips

    This function is used to check the cause when the navigation receiver assembly screen is blacked out.


    1. Check software error history.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.

      5. When an item is stored for Software Error History, record it before repairing the navigation receiver assembly.

        Software Error History Screen Description
        Error Description Trigger Detail
        Software Reset Navi Microcomputer Hexadecimal Number
        Audio Microcomputer
        CAN Microcomputer
        No Video Signal Front Monitor
        Rear Monitor
        MOST Cold Restart Always

        Tech Tips


        • Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

    2. Clear software error history.


      1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well Click here.


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  14. CHECK OPTICAL DISC ERROR HISTORY

    Tech Tips

    This function is used to check the cause when an optical disc error occurs.


    1. Check optical disc error history.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.

      5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

        Optical Disc Error History Screen Description
        Display Content
        Error Type Displays the type of error.
        Device Displays the malfunctioning device.
        Date Displays the date and time that the malfunction occurred.
        "Error Type" Screen Description
        Error Type Detection Condition Action
        Read Error When a disc read error occurs.

        Proceed to next suspected area shown in Problem Symptoms Table Click here

        Disc damaged/upside down/dirty

        When it is determined that any of the following is the cause of the disc read error:


        • The disc cannot be read.

        • The disc cannot be read because of dirt or scratches.

        • The disc cannot be read because it is inserted upside down.
        Cannot determine disc type An unsuitable disc is inserted.
        DSP error When an error occurs while decoding MP3/WMA/AAC files.
        Some files are corrupt

        • When MP3/WMA/AAC files cannot be played back because they are unsupported.

        • Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.
        Some files cannot be found

        • When a disc without music data is played back.

        • When there are no playable MP3/WMA/AAC files.
        Copy protection violation When a file with copyright protection that cannot be played back is played back.
        "Device" Screen Description
        Device Content
        DVD-P Navigation receiver assembly
        CD-P Not available
        R-Seat DVD-P Television display assembly*

        • *: w/ Rear Seat Entertainment System

        Tech Tips


        • Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

    2. Clear optical disc error history.


      1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well Click here.


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  15. CHECK VIDEO DEVICE CONNECTION CHECK

    Tech Tips


    • This function is used to detect disconnection of the video devices.

    • In order to inspect the RSE, a disc should be inserted into the navigation receiver assembly.


    1. Check Video Device Connection Check.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.

      5. When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

        Tech Tips


        • DTCs are stored when errors are detected.

        • Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.

        Video Device Connection Check Screen Description
        Error Detected Image Line (Type) Areas to be Checked
        H/U - > Separate Display (GVIF) Not available
        H/U - > Full RSE (GVIF) Not available
        RSE - > Seat Back Display RH (GVIF) Not available
        RSE - > Seat Back Display LH (GVIF) Not available
        Rear Camera - > H/U (NTSC) NTSC video signal between the navigation receiver assembly and television camera assembly
        IPA/BGM/PVM ECU - > Separate Display (GVIF) Not available
        IPA/BGM/PVM ECU - > H/U (NTSC) NTSC video signal between the navigation receiver assembly and parking assist ECU
        IPA/BGM/PVM ECU - > H/U (GVIF) Not available

    2. Clear video device connection check.


      1. When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well Click here.


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  16. MAP INFORMATION (except Pioneer Made)

    Tech Tips

    This function is used to check the map version of the navigation system and the end date of the map update service.


    1. Check map information.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Map Information.

      5. Check the map version and the end date of the map update service.

  17. MAP INFORMATION (For Pioneer Made)

    Tech Tips

    This function is used to check the map version of the navigation system.


    1. Check map information.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Map Information.

      5. Check the map version.

  18. TOYOTA LINK RESET PROCEDURE (w/ Toyota Link Function)


    1. Duplicate the problem symptom.

    2. Check cellular phone compatibility.


      1. Check if the cellular phone/vehicle is compatible (Refer to http://www.toyota.com.au/).

      2. If the cellular phone is not compatible, recommend to the customer a compatible cellular phone.

    3. Delete all paired devices from the cellular phone.


      1. This procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    4. Remove the Toyota Link app from the phone.

      Note

      Only perform this step if the customer is present and approves.


      1. The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    5. Reset the phone.

      Note

      Only perform this step if the customer is present and approves.


      1. Turn off the phone and remove the battery for 15 seconds. For instructions on how to reset cellular devices, refer to the appropriate manufacturer's website.

    6. Reinstall the Toyota Link app on the phone (if removed).


      1. This procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    7. Delete all personal data from the navigation receiver assembly.


      1. Delete all personal data from the navigation receiver assembly.

        Note

        Only perform this step if the customer is present and approves.

        Tech Tips

        Re-installation of applications must be completed before applications will appear on the navigation receiver assembly.

    8. Disconnect the cable from the negative (-) battery terminal.


      1. Record all radio station presets.

      2. Disconnect the cable from the negative (-) battery terminal and leave it disconnected for 2 minutes.

    9. Check if the problem symptom has been repaired.