NAVIGATION SYSTEM (for Navigation Receiver Type), Diagnostic DTC:B157D

DESCRIPTION

This DTC is stored when a malfunction occurs in the digital audio broadcasting antenna assembly which is connected to the navigation receiver assembly.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK FOR DTC

   
   

   1. Clear the DTCs Click here.

   2. Check for DTCs Click here.

      OK
      No DTCs are output.

   
   

   NG

   CHECK OPTIONAL COMPONENTS Click here

   OK

   USE SIMULATION METHOD TO CHECK Click here

2. CHECK OPTIONAL COMPONENTS

   
   

   1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      OK
      Optional components are installed.

      Note

      Do not remove optional components without permission of the customer.

   
   

   NG

   INSPECT WINDSHIELD GLASS ANTENNA WIRE Click here

   OK

   REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. INSPECT WINDSHIELD GLASS ANTENNA WIRE

   
   

   1. Inspect the windshield glass antenna wire Click here.

   
   

   NG

   REPAIR WINDSHIELD GLASS ANTENNA WIRE Click here

   OK

4. CHECK NAVIGATION RECEIVER ASSEMBLY

   
   

   1. Remove the antenna connector from the navigation receiver assembly.

   2. Turn the engine switch on (ACC) with the navigation receiver assembly connector connected.

   3. Turn on the radio and turn into AM mode.

   4. Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK
      Noise occurs.

   
   

   NG

   REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

   OK

5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 2 ANTENNA CORD SUB-ASSEMBLY)

   
   

   1. Disconnect the DB navigation receiver assembly connector.

   2. Disconnect the antenna connector from the No.2 antenna cord sub-assembly.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 1 - 1 Always Below 1 Ω 1-a - 1-a Always Below 1 Ω 1 - Body ground Always 10 kΩ or higher 1-a - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

6. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY

   
   
   1. 

      Text in Illustration

      *a	Front view of wire harness connector (to Digital Audio Broadcasting Antenna Assembly LH)
      *b	Front view of wire harness connector (to Vehicle Wire Harness)

      Disconnect the antenna connector from the navigation receiver assembly.

   2. Disconnect the antenna connector from the digital audio broadcasting antenna assembly LH.

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 1 - 1 Always Below 1 Ω 1-a - 1-a Always Below 1 Ω 1 - Body ground Always 10 kΩ or higher 1-a - Body ground Always 10 kΩ or higher

   
   

   NG

   REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY Click here

   OK

7. CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH

   
   

   1. Replace the digital audio broadcasting antenna assembly LH with a known good one Click here.

   2. Clear the DTCs Click here.

   3. Check for DTCs Click here.

      OK
      No DTCs are output.

   
   

   NG

   CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH Click here

   OK

   END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY LH IS DEFECTIVE)

8. CHECK DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH

   
   

   1. Replace the digital audio broadcasting antenna assembly RH with a known good one Click here.

   2. Clear the DTCs Click here.

   3. Check for DTCs Click here.

      OK
      No DTCs are output.

   
   

   NG

   REPLACE NAVIGATION RECEIVER ASSEMBLY Click here

   OK

   END (DIGITAL AUDIO BROADCASTING ANTENNA ASSEMBLY RH IS DEFECTIVE)