CLEARANCE WARNING BUZZER INSTALLATION


  1. INSTALL NO. 1 CLEARANCE WARNING BUZZER


    1. Attach the clamp to install the No. 1 clearance warning buzzer.

    2. Connect the connector.

  2. INSTALL DISPLAY AND NAVIGATION MODULE DISPLAY (w/ Navigation System)


    1. Connect each connector.

    2. A01DQZF

      Insert the navigation receiver assembly and attach the 7 clips on the backside of the navigation receiver assembly.

      Note

      When inserting the receiver, do not press the knobs on it.

    3. Install the navigation receiver assembly with the 4 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  3. INSTALL RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)


    1. Connect each connector.

    2. A01DQWH

      Insert the radio receiver assembly to attach the 2 guides on its backside.

      Note

      When inserting the receiver, do not press the knobs on it.

    3. Install the radio receiver assembly with the 4 bolts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  4. INSTALL RADIO TUNER OPENING COVER (w/o Audio)


    1. Install the radio tuner opening cover with the 4 bolts.

  5. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Navigation System)


    1. Connect each connector.

    2. Attach the 10 clips to install the center instrument cluster finish panel.

  6. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. Connect the connector.

    2. Attach the 4 clips to install the integration control and panel assembly.

  7. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. A01DTNY

      Connect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  8. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. Connect each connector and each cable.

    2. w/o Knee Airbag:


      1. Attach the 7 clips to install the lower instrument panel finish panel.

    3. w/ Knee Airbag:


      1. Attach the 14 clips to install the lower instrument panel finish panel.

    4. Install the 2 bolts <C>.

    5. Attach the 2 claws to close the cover.

  9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. Connect each connector.

    2. Attach the 4 clips to install the instrument panel finish panel.

  10. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. for LHD:


      1. Attach the 2 clips and 2 guides to install the No. 1 instrument panel under cover.

      2. Install the screw.

    2. for RHD:


      1. Attach the 3 clips and 2 guides to install the No. 1 instrument panel under cover.

      2. Install the screw.

  11. INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)


    1. Attach the 3 clips to install the instrument cluster finish panel ornament.

  12. INSTALL INSTRUMENT SIDE PANEL LH (for LHD)


    1. Attach the 5 clips, claw and 3 guides to install the instrument side panel.

  13. INSTALL COWL SIDE TRIM BOARD LH (for LHD)


    1. Attach the clip and claw to install the cowl side trim board.

    2. Install the clip.

  14. INSTALL DOOR SCUFF PLATE ASSEMBLY LH (for LHD)


    1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate.

  15. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

    2. Install the screw.

      A01DNTKE01
      Text in Illustration
      *A for LHD *B for RHD

  16. INSTALL INSTRUMENT SIDE PANEL RH (for RHD)


    1. Attach the 5 clips, claw and 3 guides to install the instrument side panel RH.

  17. INSTALL COWL SIDE TRIM BOARD RH (for RHD)


    1. Attach the clip and claw to install the cowl side trim board RH.

    2. Install the clip.

  18. INSTALL DOOR SCUFF PLATE ASSEMBLY RH (for RHD)


    1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly RH.

  19. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)


    1. Connect each connector.

    2. Attach the 4 clips to install the instrument panel finish plate garnish.

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  21. CHECK SRS WARNING LIGHT

    Click here