CLEARANCE WARNING BUZZER REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH (for LHD)

    A01DNTTE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

      Tech Tips

      Tape the screwdriver tip before use.

  4. REMOVE COWL SIDE TRIM BOARD LH (for LHD)

    A01DQEI

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board.

  5. REMOVE INSTRUMENT SIDE PANEL LH (for LHD)

    A01DNBCE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel.

    2. Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.

  6. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

    A01DM0OE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument cluster finish panel ornament.

    2. Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

    Tech Tips

    Use the same procedure described for the No. 2 instrument panel finish panel cushion.

  8. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

    A01DREC

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish plate garnish.

  9. REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD)

    A01DQUSE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the door scuff plate assembly RH.

    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate assembly RH.

      Tech Tips

      Tape the screwdriver tip before use.

  10. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

    A01DN9Y

    1. Remove the clip.

    2. Detach the clip and claw and remove the cowl side trim board RH.

  11. REMOVE INSTRUMENT SIDE PANEL RH (for RHD)

    A01DUSZE01
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape around the instrument side panel.

    2. Using a moulding remover, detach the 5 clips, claw, and 3 guides.

    3. Disconnect the connector and remove the instrument side panel.

  12. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

    2. Install the screw.

      A01DNTKE01
      Text in Illustration
      *A for LHD *B for RHD

  13. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

    A01DP35

    1. Detach the 4 clips.

    2. Disconnect each connector and remove the instrument panel finish panel.

  14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

    A01DT5YE01

    1. Using a screwdriver, detach the 2 claws and open the cover.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A01DOV5

      w/o Knee Airbag:


      1. Remove the 2 bolts <C>.

      2. Detach the 7 clips.

      3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

    3. A01DPFD

      w/ Knee Airbag:


      1. Remove the 2 bolts <C>.

      2. Detach the 14 clips.

      3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

  15. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. A01DQSY

      Remove the 4 bolts and airbag assembly.

    2. Disconnect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  16. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01DQRN

      Detach the 4 clips.

    2. Disconnect the connector and remove the integration control and panel assembly.

  17. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Navigation System)

    A01DQVK

    1. Detach the 10 clips and remove the center instrument cluster finish panel.

    2. Disconnect each connector.

  18. REMOVE RADIO TUNER OPENING COVER (w/o Audio)

    A01DTOF

    1. Remove the 4 bolts and radio tuner opening cover.

  19. REMOVE RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)


    1. A01DQWH

      Remove the 4 bolts.

    2. Pull the radio receiver assembly to detach the 2 guides on the backside of the radio receiver assembly.

    3. Disconnect each connector and remove the radio receiver assembly.

  20. REMOVE DISPLAY AND NAVIGATION MODULE DISPLAY (w/ Navigation System)


    1. A01DMHI

      Remove the 4 bolts.

    2. A01DO05

      Pull the navigation receiver assembly to detach the 7 clips on the backside of the navigation receiver assembly.

    3. Disconnect each connector and remove the navigation receiver assembly.

  21. REMOVE NO. 1 CLEARANCE WARNING BUZZER

    A01DMHA

    1. Disconnect the connector.

    2. Detach the clamp and remove the No. 1 clearance warning buzzer.