TELEVISION CAMERA (for Side) REMOVAL


  1. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH


    1. Remove the outer rear view mirror Click here.

  2. REMOVE OUTER REAR VIEW MIRROR GLASS

    A01DOG7E01
    Text in Illustration
    *1 Protective Tape

    1. Push the upper part of the mirror surface and tilt it.

    2. Using a moulding remover, detach the 4 claws and separate the outer rear view mirror glass from the mirror body.

      Tech Tips

      Apply protective tape to the outer rear view mirror to prevent it from being damaged.

    3. Disconnect the connectors and remove the mirror glass.

  3. REMOVE OUTER MIRROR COVER

    A01DREQE02

    Tech Tips

    Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.


    1. A01DN3EE01
      Text in Illustration
      *1 Protective Tape

      Using 2 screwdrivers, detach the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

      Note

      Be careful not to break the ribs.

      Tech Tips

      Tape the screwdriver tip before use.

      A01DPMIE01
      Text in Illustration
      *1 Protective Tape *2 Rib
      *a Inner Side of Outer Mirror Cover - -
    3. A01DTFLE01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

      Note

      Do not insert the moulding remover more than 4 mm (0.157 in.).

      Tech Tips

      Tape the moulding remover before use.

    4. A01DT4YE01

      Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

      Note


      • Do not insert the moulding remover more than 4 mm (0.157 in.).

      • Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

      Standard
      Area Specified Condition
      a 40.0 mm (1.57 in.)

    5. Remove the moulding remover.

    6. A01DNKME01
      Text in Illustration
      *1 Protective Tape

      Insert a moulding remover between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.

    7. A01DN6SE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

    8. A01DUF1

      Detach the 2 claws and remove the outer mirror cover.

      Note

      When removing the cover, be careful not to damage the side turn signal light assembly or cover.

  4. REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH


    1. A01DQT6

      Remove the 3 screws and light.

    2. Disconnect the connector.

  5. REMOVE SIDE TELEVISION CAMERA ASSEMBLY


    1. A01DUMSE01
      Text in Illustration
      *1 Tape

      Remove the tape.

    2. A01DSUB

      Remove the screw, detach the 4 claws and remove the rubber base.

      Tech Tips

      It is not necessary to completely remove the rubber base. Slightly move the rubber base so that the lower mirror cover can be removed in a later step.

    3. Remove the lower mirror cover.


      1. A01DO5LE01
        Text in Illustration
        *1 Protective Tape

        Put protective tape around the lower mirror cover.

      2. A01DMUTE02
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      3. A01DR86E01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw.

      4. A01DPSSE01
        Text in Illustration
        *1 Protective Tape

        Using a screwdriver, detach the claw to create a space between the lower mirror cover and mirror body as shown in the illustration.

      5. A01DMS3E01
        Text in Illustration
        *1 Protective Tape

        Insert a screwdriver as shown in the illustration.

      6. A01DQYLE01
        Text in Illustration
        *1 Protective Tape

        Detach the claw to create a space between the lower mirror cover and mirror body as shown in the illustration.

      7. A01DNQQ

        While moving the lower mirror cover back and forth in the directions of the arrows in the illustration, detach the 3 claws and remove the lower mirror cover.

    4. A01DS8E

      Using a T25 "TORX" socket wrench, remove the 3 screws.

    5. A01DNJ9

      Remove the 5 screws.

    6. A01DSCIE01

      Using a moulding remover, open the mirror body as shown in the illustration.

    7. Using a moulding remover, detach the 2 claws.

      Note

      Be careful not to break the claw shown in the part of the illustration labeled A.

    8. A01DPHSE01

      Using a screwdriver, disconnect the connector.

      Note

      When disconnecting the connector, be careful not to damage it.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    9. A01DMLO

      Remove the 3 screws and side television camera.