REPAIR INSTRUCTION CUSTOMIZE PARAMETERS


  1. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the intelligent tester on.

    4. Enter the following menus: Body / Tilt & Telescopic / Utility / Customize.

    5. Select a new setting by referring to the table below.

      Tilt & Telescopic
      Display Default Contents Setting
      Autoaway/Return function ON Turn the auto away/return function ON or OFF ON/OFF

  2. CUSTOMIZE TOYOTA PARKING ASSIST-SENSOR SYSTEM (w/ Multi-display)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.

    • When troubleshooting a function, first make sure that the function is set to the default setting.


    1. Customizing with the GTS


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Customize Setting / Clearance Sonar / Warning, Sensor or Display.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Rr Sensor Onset Range Wide Set the buzzer activation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 650 mm (25.6 in.)

        • Wide: 1500 mm (59.1 in.)

        		 Clearance warning ECU
        Fr Sensor Onset Range Wide Set the buzzer activation range for the front center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1000 mm (39.4 in.)

        		 Clearance warning ECU
        Keep Sense Buzzer Avail Make the buzzer sound when the distance between the vehicle and obstacle does not change for more than 3 seconds.

        Not Avail or Avail


        • Not Avail: Not Available

        • Avail: Available

        		 Clearance warning ECU
        Fr & Rr Buzzer Volume M2 Change the buzzer volume setting.

        L, M1, M2, M3 or H


        • L: Low volume

        • M1: Medium low volume

        • M2: Medium volume

        • M3: Medium high volume

        • H: High volume

        		 Clearance warning ECU
        Sensor Condition N Avail Make the front sensors available when the shift lever is in N.

        Not Avail or Avail


        • Not Avail: Not Available

        • Avail: Available

        		 Clearance warning ECU
        Reverse Range Front Sensor Fcrn Change the operation setting for the front sensors when the shift lever is in R.

        F, Fcrn or F Stop


        • F: Front sensors are available

        • Fcrn: Front corner sensors are available

        • F Stop: Front sensors are not available

        		 Clearance warning ECU
        Non P/R Range Rear Sensor R Stop Change the operation setting for the rear sensors when the shift lever is in any position except P or R.

        R, Rcrn or R Stop


        • R: All rear sensors are available

        • Rcrn: Rear corner sensors are available

        • R Stop: All rear sensors are not available

        		 Clearance warning ECU
        Display Mode All Change the display mode setting (when the TOYOTA parking assist-sensor system is normal). All or Undisp Clearance warning ECU

    2. Customizing with Multi-display


      1. Turn the engine switch on (IG).

      2. Enter the following menus: Setup / Vehicle / TOYOTA Park Assist.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant
        Alert volume 3 Change the buzzer volume setting.

        1, 2, 3, 4 or 5


        • 1: Low volume

        • 2: Medium low volume

        • 3: Medium volume

        • 4: Medium high volume

        • 5: High volume

        		 Clearance warning ECU
        Display On Change the display mode setting (when the TOYOTA parking assist-sensor system is normal). On or Off Clearance warning ECU
        Distance Wide Set the buzzer activation range for the front center sensors.

        Narrow or Wide


        • Narrow: 600 mm (23.6 in.)

        • Wide: 1000 mm (39.4 in.)

        		 Clearance warning ECU
        Set the buzzer activation range for the rear center sensors.

        Narrow or Wide


        • Narrow: 650 mm (25.6 in.)

        • Wide: 1500 mm (59.1 in.)

        		 Clearance warning ECU

  3. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch ON.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Customize Setting / Door Lock.

      5. Select the setting by referring to the table below.

        Door Lock
        Display Default Content Setting Relevant ECU
        Unlock Key Twice OFF Function that unlocks only the driver door when the driver door key cylinder is turned to unlock once, and unlocks all doors when it is turned to unlock twice. For the OFF setting, turning it once unlocks all doors ON or OFF Main body ECU (multiplex network body ECU)
        Auto Lock* ON Function that locks all doors when the vehicle speed reaches a certain level ON or OFF Main body ECU (multiplex network body ECU)
        Auto Lock/Shift* OFF Function that locks all doors when the shift lever is moved from P to any position other than P while the engine is running and all doors are closed ON or OFF Main body ECU (multiplex network body ECU)
        Auto Unlock/Shift* OFF Function that unlocks all doors when the shift lever is moved to P from any position other than P while the ignition switch is ON ON or OFF Main body ECU (multiplex network body ECU)
        All Unlock/Open-Close* OFF Function that unlocks the other doors when the driver door is opened within 43 seconds after the ignition switch is turned off ON or OFF Main body ECU (multiplex network body ECU)

        • *: w/ Collision door lock release function

  4. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Customize Setting / Wireless Door Lock.

      5. Select the setting by referring to the table below.

        Wireless Door Lock
        Display Default Content Setting Relevant ECU
        Wireless Control ON The function that turns the wireless door lock on or off ON or OFF Main body ECU (multiplex network body ECU)
        Hazard Answer Back ON When the lock switch on the transmitter is pressed, this function illuminates the hazard warning lights and side turn signal lights once. When the unlock switch is pressed, the hazard warning lights and side turn signal lights illuminate twice ON or OFF Main body ECU (multiplex network body ECU)
        Open Door Warning*1 ON If a door is not completely closed and the transmitter lock switch is pressed, this function makes the buzzer sound for 5 seconds ON or OFF Main body ECU (multiplex network body ECU)
        Unlock 2 Operation OFF The function that unlocks the driver side door when the unlock switch on the transmitter is pressed once, and unlocks all the doors when pressed twice. If the setting is off, pressing the unlock switch once makes all the doors unlock ON or OFF Main body ECU (multiplex network body ECU)
        Auto Lock Time 30 s The function that changes the time until relocking after unlocking the doors with the wireless door lock function 30 s, 60 s or 120 s Main body ECU (multiplex network body ECU)
        Wireless Buzzer Resp*2 ON This function turns the wireless door lock buzzer response on or off ON or OFF Main body ECU (multiplex network body ECU)
        Wireless Glass Hatch Open*3 Long1 This function changes the operation method of opening the glass hatch by the transmitter 1tim ON, 2tim ON, Long1, Long2 or Prohibit Main body ECU (multiplex network body ECU)
        P/W Ope buzzer ON This function turns the wireless power window buzzer response on or off ON or OFF Main body ECU (multiplex network body ECU)
        Wireless Buzzer Vol*2 Level7 This function changes the wireless door lock buzzer volume Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0 Main body ECU (multiplex network body ECU)

        • *1: w/ Door Ajar Waning Function

        • *2: w/ Wireless Buzzer Answer-back

        • *3: w/ Glass Hatch Opener System

  5. CUSTOMIZE WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch ON.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Customize Setting / Wireless Door Lock.

      5. Select the setting by referring to the table below.

        Wireless Door Lock
        Display Default Content Setting Relevant ECU
        Wireless Control ON The function that turns the wireless door lock on or off ON or OFF Main body ECU (multiplex network body ECU)
        Hazard Answer Back ON When the lock switch on the transmitter is pressed, this function illuminates the hazard warning lights and side turn signal lights once. When the unlock switch is pressed, the hazard warning lights and side turn signal lights illuminate twice ON or OFF Main body ECU (multiplex network body ECU)
        Open Door Warning ON If a door is not completely closed and the transmitter lock switch is pressed, this function makes the buzzer sound for 5 seconds ON or OFF Main body ECU (multiplex network body ECU)
        Unlock 2 Operation OFF The function that unlocks the driver side door when the unlock switch on the transmitter is pressed once, and unlocks all the doors when pressed twice. If the setting is off, pressing the unlock switch once makes all the doors unlock ON or OFF Main body ECU (multiplex network body ECU)
        Auto Lock Time 30 s The function that changes the time until relocking after unlocking the doors with the wireless door lock function 30 s, 60 s or 120 s Main body ECU (multiplex network body ECU)
        Wireless Buzzer Resp*1 ON This function turns the wireless door lock buzzer response on or off ON or OFF Main body ECU (multiplex network body ECU)
        Wireless Glass Hatch Open*2 Long1 This function changes the operation method of opening the glass hatch by the transmitter 1tim ON, 2tim ON, Long1, Long2 or Prohibit Main body ECU (multiplex network body ECU)
        P/W Ope buzzer ON This function turns the wireless power window buzzer response on or off ON or OFF Main body ECU (multiplex network body ECU)
        Wireless Buzzer Vol*1 Level7 This function changes the wireless door lock buzzer volume Level7, Level6, Level5, Level4, Level3, Level2, Level1 or Level0 Main body ECU (multiplex network body ECU)

        • *1: w/ Wireless Buzzer Answer-back

        • *2: w/ Glass Hatch Opener System

  6. CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current setting before customizing.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus: Utility / Customize.

      5. Select the setting by referring to the table below.

        Entry&Start
        Display Default Contents Setting
        Park Wait Time (Waiting time to permit unlocking door after locking) 2.5s Function that sets the waiting time to permit unlocking the door after the door is locked with the entry lock function. 0.5s, 1.5s, 2.5s or 5s

        Ignition Available Area

        (Entry ignition available area)

        		 All Function to choose the available area for the key to start the engine and cancel the steering lock. Front or All
        Glass Hatch Open Operation ON Function to permit opening the glass hatch with the electronic key. ON or OFF
        Warning
        Display Default Contents Setting
        Key Low Battery Warning (Warn when key battery becomes weak) ON Function that warns the driver that the key battery power is low. ON or OFF

    2. Customizing with Multi-display


      1. Turn the engine switch on (IG).

      2. Select the following menus: Setup / Vehicle / Vehicle Customization / Door Lock Settings.

      3. Select the setting by referring to the table below.

        Display Default Content Setting Relevant ECU
        Select doors to unlock Driver Function that sets which doors are unlocked by the entry unlock function. All or Driver Certification ECU
        Entry and start system On Function that enables or disables the smart access system with push-button start. On or Off Certification ECU

    3. Entry unlock mode switching function (manual operation)


      1. To use the entry unlock mode switching function, make sure the engine switch is off and simultaneously press and hold the lock switch on the key and another key switch for 5 seconds.


        • When the switches are pressed and held for 5 seconds, the entry door unlock mode changes in the following order: all door unlock mode, driver door unlock mode.

        Note

        After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.


        • All door unlock mode (default):

          When a touch sensor is touched, all the doors unlock.

        • Driver door unlock mode:

          When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all the doors unlock.

      2. The certification ECU receives the signal from the key and changes the entry and start system to the appropriate entry unlock mode.

      3. The certification ECU sounds the wireless door lock buzzer and combination meter buzzer to inform the user that the mode has been switched.

        Mode Wireless Door Lock Buzzer Combination Meter Assembly (Buzzer)

        All Doors

        (Default)

        		 Sounds 2 times Sounds once

        Driver Door

        (Customized)

        		 Sounds 3 times Sounds once

        Tech Tips

        The function only changes the entry unlock mode of the entry and start system. It does not switch the unlocking of the wireless door lock control.

    4. Entry cancel function (manual operation)


      • The key cancel operation disables the following functions:


        • Entry Unlock/Lock

        • Key Lock-in Prevention

        • Entry Back Door Open

        • Entry Glass Hatch Open (w/ Glass Hatch Opener System)

        • Warning

        • Entry Ignition

        • Memory Call (w/ Memory)


      1. The operation procedures are as follows:


        • Precondition:

        • Engine switch off, driver side door closed and unlocked.


        1. Unlock the driver side door once with the unlock switch of the key.

        2. Open the driver door within 5 seconds.

        3. Unlock the driver side door twice with the unlock switch of the key within 5 seconds.

        4. Close and open the driver door twice within 30 seconds.

          (Driver door: Open condition → Close → Open → Close → Open)

        5. Unlock the driver side door twice with the unlock switch of the key within 5 seconds.

        6. Close and open the driver door once within 30 seconds.

          (Driver door: Open condition → Close → Open)

        7. Close the driver door within 5 seconds.

          When key cancel is activated, the wireless door lock buzzer sounds twice.

          To return to the original condition, perform the procedure again. When the original condition is restored, the wireless door lock buzzer sounds once.

  7. CUSTOMIZE THEFT DETERRENT SYSTEM

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Be sure to make a note of the current settings before customizing.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Utility / Customize.

      5. Select the setting by referring to the table below.

        Security
        Display Default Contents Setting
        Intrusion Win Opened*1 OFF The function to change the sensitivity of the intrusion sensor when a window is open. ON or OFF
        Security control with mechanism key*2 OFF This function makes it possible to cancel the security alarm with the mechanical key. ON or OFF

        • *1: w/ Intrusion Sensor

        • *2: Vehicles displaying the Item "Security control with mechanism key" on the intelligent tester

  8. CUSTOMIZE LIGHTING SYSTEM (for Interior)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Customize Setting / Illuminated Entry.

    5. Select the setting by referring to the table below.

      Illuminated Entry
      Tester Display Default Content Setting
      Lighting Time 15 s Changes the lighting time after closing all of the doors (the lights will fade out immediately when turning the ignition switch from off to ACC or ON). 7.5 s, 15 s or 30 s
      I/L when ACC OFF ON This function turns on the lights when the ignition switch is turned from ON or ACC to off (the room light turns on when the interior light switch is set to DOOR). ON or OFF
      I/L ON W/Door Key Unlock*2 ON This function turns on the room light when the door is unlocked with the door key cylinder (the room light turns on when the map light switch is set to DOOR). ON or OFF
      Light Control ON This function controls the interior foot lights, inside handle illumination, ornament illumination and door pocket illumination. ON or OFF
      Room Light when Aprchd*1 ON This function turns on the room light when the key is brought within the vehicle exterior detection area (the room light turns on when the map light switch is set to DOOR). ON or OFF
      Inside Foot Light*3 ON This function controls the interior foot lights. ON or OFF
      Center Console Spot Light ON Lights up the center console spot light when the ignition switch is turned to ACC or ON. ON or OFF
      Mirror Foot Light Time*4 15 s Side step light illumination duration. 0 s, 7.5 s, 15 s or 30 s
      Interior Light Control ON This function controls the interior lights. ON or OFF
      Exterior Light Control*4 ON This function controls the side step lights. ON or OFF
      Scuff Plate Lamp linked to Entry & Start*4 ON This function turns on the side step light when the key is brought within the vehicle exterior detection area. ON or OFF
      Scuff Plate Lamp linked to Wireless Key*4 ON This function turns on the side step light when the door is unlocked with the wireless key. ON or OFF
      Scuff Plate Lamp linked to D-Door Unlock SW*4 ON This function turns on the side step light when the door is unlocked with the manual unlock switch. ON or OFF
      Scuff Plate Lamp linked to Door open*4 ON This function turns on the side step light when the driver door is opened. ON or OFF

      • *1: w/ Entry and Start System

      • *2: w/o Entry and Start System

      • *3: w/ Interior Foot Light

      • *4: w/ Side Step Light

    6. Customizing with the Multi-display


      1. Turn the ignition switch to ON.

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Lights settings.

      3. Select the setting by referring to the table below.

        Vehicle settings
        Tester Display Default Content Setting
        Interior light off timer 15 s Changes the lighting time of the following lights that are operated by the timer function when the door switch of the map light assembly is on: Off, 7.5 s, 15 s or 30 s

  9. CUSTOMIZE METER / GAUGE SYSTEM


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch ON.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Customize Setting / Warning or Display.

      5. Select the setting by referring to the table below.

        Warning
        Display Default Content Setting Relevant ECU
        Driver Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly
        Front Passenger Side Seatbelt Warning Buzzer* ON Function to turn on/off the seat belt warning buzzer ON or OFF Combination meter assembly

        • *: This setting is only valid for the buzzer which sounds at 20 km/h (12 mph) or more

        Display
        Display Default Content Setting Relevant ECU
        Units By Region*1, *2 Units of Destination Function to change the unit of the display Km/l JP, Km/l, Mi/g US or Mi/g UK Combination meter assembly
        Language*1, *2 Language of Destination Function to change the language of the display Eng US, Eng UK, French, German, Spanish, Italian, Japanese, CHN Sim, CHN Trd or Russian Combination meter assembly
        ECO Drive Indicator*3 ON Function to enable or disable eco driving indicator zone display in the multi-information display ON or OFF Combination meter assembly

        • *1: for Analog Meter

        • *2: except 5L-E

        • *3: for Automatic Transmission

  10. CUSTOMIZE SEAT BELT WARNING SYSTEM

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with the intelligent tester


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Utility / Customize Setting.

      5. Select the setting by referring to the table below.

        Seat Belt Warning
        Display Default Contents Setting
        Driver Side Seatbelt Warning Buzzer ON If the driver side seat belt is unfastened and the vehicle is driven at approximately 20 km/h (12.5 mph) or more, the system sounds the seat belt warning buzzer. ON or OFF
        Front Passenger Side Seatbelt Warning Buzzer ON If the front passenger side seat belt is unfastened with the front passenger seat occupied and the vehicle is driven at approximately 20 km/h (12.5 mph) or more, the system sounds the seat belt warning buzzer. ON or OFF

  11. CUSTOMIZE AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Customizing with intelligent tester.


      1. Connect the intelligent tester to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the intelligent tester on.

      4. Enter the following menus: Body / Air Conditioner / Utility / Customize.

      5. Select the setting by referring to the table below.

        Air Conditioner
        Display Default Contents Setting
        Set Temperature Shift Normal Function to set the temperature shift. +2 C, +1 C, Normal, -1 C or -2 C
        Compressor Mode Automatic Function to turn the A/C on automatically by pressing the AUTO button when the blower is on and the A/C is off. Automatic or Manual
        Air Inlet Mode Automatic Function to automatically change to recirculation mode when the A/C is turned on. Automatic or Manual
        Foot/DEF Auto Mode ON Function to turn on the airflow from the front and rear footwell register ducts and front defroster automatically when auto mode is on. ON or OFF
        Foot/DEF Automatic Blow Up Function ON Function to change the blower level automatically when the front defroster is on. ON or OFF
        Add Foot Air in FACE Mode ON When the FACE mode is selected, an additional amount of air is blown to the foot area. ON or OFF

    2. Customizing with Multi-display


      1. Turn the engine switch on (IG).

      2. Select the following menus: Setup / Vehicle / Vehicle Customization.

      3. Select the setting by referring to the table below.

        Climate Settings
        Display Default Content Setting Relevant ECU
        Smog Sensor Sensitivity

        0

        (middle bar)

        		 Function to change the sensitivity of the exhaust gas sensor. +3, +2, +1, 0, -1, -2 or -3 Air conditioning amplifier assembly
        Auto A/C Mode On Function to turn the A/C on automatically by pressing the AUTO button when the blower is on and the A/C is off. On or Off Air conditioning amplifier assembly

  12. CUSTOMIZE POWER WINDOW CONTROL SYSTEM

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Customize Setting / Power Window.

    5. Select the setting by referring to the table below.

      Display Default Content Setting
      Door Key P/W Up OFF This function is used to close the windows by operating the mechanical key. ON or OFF
      Door Key P/W Down OFF This function is used to open the windows by operating the mechanical key. ON or OFF
      P/W Up w/ Transmitter OFF This function is used to close the windows using the wireless key transmitter. ON or OFF
      P/W Down w/ Transmitter OFF This function is used to open the windows using the wireless key transmitter. ON or OFF
      P Window Auto Up Avail This function is used to enable or disable the auto up function for the front passenger door window using the power window regulator switch assembly (for front passenger side). Avail or Not Avl
      P Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the front passenger door window using the master switch. Avail or Not Avl
      RR Window Auto Up Avail This function is used to enable or disable the auto up function using the rear power window regulator switch assembly RH. Avail or Not Avl
      RR Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear RH door window using the master switch. Avail or Not Avl
      RL Window Auto Up Avail This function is used to enable or disable the auto up function using the rear power window regulator switch assembly LH. Avail or Not Avl
      RL Window Auto Up From Driver Avail This function is used to enable or disable the remote auto up function for the rear LH door window using the master switch. Avail or Not Avl

  13. CUSTOMIZE SLIDING ROOF SYSTEM

    Tech Tips


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Utility / Customize Setting.

    5. Select the setting by referring to the table below.

      Slide Roof
      Display Default Contents Setting
      Door Key Related Open*1 ON The function to manually open the sliding roof linked with the power windows by holding the driver side door key for 2.0 seconds or more to the unlock position when the ignition switch is off. ON or OFF
      Door Key Related Close*1 ON The function to manually close the sliding roof linked with the power windows by holding the driver side door key for 2.0 seconds or more to the lock position when the ignition switch is off. ON or OFF
      Wireless Key Related Open*2 ON The function to manually open the sliding roof linked with the power windows by pressing the transmitter UNLOCK switch for 3.0 seconds or more when the ignition switch is off. ON or OFF
      Wireless Key Related Close*2 ON The function to manually close the sliding roof linked with the power windows by pressing the transmitter LOCK switch for 3.0 seconds or more when the ignition switch is off. ON or OFF
      Door Key Related Operation Slide The function to select tilt up or slide open of the manual sliding roof operation linked with the power windows by holding the driver side door key for 2.0 seconds or more to the unlock position when the ignition switch is off. Slide or Tilt
      Wireless Key Related Operation Slide The function to select tilt up or slide open of the manual sliding roof operation linked with the power windows by pressing on the transmitter UNLOCK switch for 3.0 seconds or more when the ignition switch is off. Slide or Tilt

      Note


      • *1: This function is linked with the power window key-linked function. If the power window key-linked function is set to OFF, the sliding roof key-linked function will not operate even when it is set to ON.

      • *2: This function is linked with the power window wireless transmitter-linked function. If the power window wireless transmitter-linked function is set to OFF, the sliding roof wireless transmitter-linked function will not operate even when it is set to ON.

  14. CUSTOMIZE LIGHTING SYSTEM (for Exterior)

    Tech Tips

    The following items can be customized.

    Note


    • When the customer requests a change in a function, first make sure that the function can be customized.

    • Record the current settings before customizing.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the intelligent tester on.

    4. Enter the following menus: Customize Setting / Light Control.

    5. Select the setting by referring to the table below.

      Light Control
      Display Default Content Setting
      Response Time Normal Changes the delay timing of illuminating the taillights when going into a tunnel when the headlight dimmer switch is in the AUTO position. Long or Normal
      Sensitivity Normal Function to adjust the ambient light sensitivity of the automatic light control system.*1 Light2, Light1, Normal, Dark1 or Dark2
      Disp Ex ON Sen Normal Function to change the level of ambient light at which the system dims lights such as the indicator lights of the combination meter, the A/C indicator light and the clock.*2 Light2, Light1, Normal, Dark1 or Dark2
      Disp Ex OFF Sen Normal Function to change the level of ambient light at which the system cancels the dimming of lights such as the indicator lights of the combination meter, the A/C indicator light and the clock.*3 Light2, Light1, Normal, Dark1 or Dark2
      Light Auto OFF Delay 30s Function to continue illuminating the headlights for a certain period of time after closing all the doors with the ignition switch turned from ON to off under the condition that the headlight dimmer switch is in the head or AUTO position with the headlights on. OFF, 30s, 60s or 90s

      Tech Tips

      The sensitivity adjustment may be difficult to confirm. Check by driving the customer's vehicle.

      *1
      System Setting A01DQ4Z
      Setting Dark2 Dark1 Normal Light1 Light2

      Tech Tips

      When the setting is closer to the "Light" side, the system turns the lights on even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before turning on the lights.

      *2
      System Setting A01DQ4Z
      Setting Dark2 Dark1 Normal Light1 Light2

      Tech Tips

      When the setting is closer to the "Light" side, the system dims the indicator lights even when the surrounding area is relatively bright. When the setting is closer to the "Dark" side, the system waits until the surrounding area is darker before dimming the indicator lights.

      *3
      System Setting A01DQ4Z
      Setting Dark2 Dark1 Normal Light1 Light2

      Tech Tips

      When the setting is closer to the "Dark" side, the system cancels the dimming of the indicator lights even when the surrounding area is relatively dark. When the setting is closer to the "Light" side, the system waits until the surrounding area is brighter before canceling the dimming of the indicator lights.

    6. Customizing with the Multi-display


      1. Turn the ignition switch to ON.

      2. Enter the following menus: MENU / Setup / Vehicle / Vehicle customization / Lights settings.

      3. Select the setting by referring to the table below.

        Vehicle settings
        Display Default Content Setting
        Light sensor sensitivity 0 Adjusts the sensitivity of the automatic light control system.*1 -2, -1, 0, +1 or +2
        Headlamps auto-off timer 30s Keep the headlights on for a certain period of time after turning the ignition switch off and closing all doors with the low beam headlights on. Off, 30s, 60s or 90s
        Daytime running lights ON ON/OFF of the DRL function On or Off
        Exterior lights off timer 15s Changes the lighting time of the door mirror foot lights. Off, 7.5s, 15s or 30s

        Tech Tips

        The sensitivity adjustment may be difficult to confirm. Check by driving the vehicle.

        *1
        Sensitivity of the automatic light control system A01DQ4Z
        Setting -2 -1 0 +1 +2