REAR DOOR BELT MOULDING INSTALLATION


  1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    1. A01HQA8

      Engage the 6 claws to install the rear door belt moulding assembly as shown in the illustration.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A01HNDZ

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  3. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. A01HMDU

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  4. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01HOFI

      Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

  5. INSTALL REAR DOOR GLASS RUN


    1. A01HP8P

      Install the rear door glass run.

  6. INSTALL REAR DOOR WEATHERSTRIP


    1. A01HOCI

      Engage the 20 clips to install the rear door weatherstrip.

  7. INSTALL REAR DOOR CHECK ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door check assembly.

    2. Apply adhesive to the threads of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    3. A01HNFI

      Install the rear door check assembly with the 2 nuts and bolt.

      Torque:
      Bolt
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }
      Nut
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  8. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. A01HPUZE01
      Text in Illustration
      *1 Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01HN57

      Install the rear door inner glass weatherstrip.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01HMOB

      Install the No. 1 door scuff plate clamp as shown in the illustration.

    2. A01HQRHE01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. A01HQXZE01
      Text in Illustration
      *1 Reference Boss

      Engage the rear door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

    4. A01HOZQ

      Engage the 8 clips and install the rear door trim board sub-assembly.

    5. Install the 3 screws.

    6. If protective tape has been applied, remove it.

  11. INSTALL REAR ARMREST ASSEMBLY


    1. A01HQTP

      Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

  12. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01HPZ1

      Engage the 4 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01HNNY

      Engage the 3 claws to install the rear door inside handle bezel plug.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSPECT POWER WINDOW OPERATION

    Click here