FRONT DOOR WINDOW FRAME MOULDING REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

    Click here

  4. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Disconnect the connector from the door side airbag sensor.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        A01HN61E12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connector Lock is Released - -

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting.

    4. A01HR0Q

      Remove the bolt and door side airbag sensor from the front door panel.

      Note

      Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01HQ1GE01
      Text in Illustration
      *a Incorrect *b Correct

  5. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01HMZD

      Remove the bolt.

    2. Disconnect each connector.

    3. Disengage the 5 clamps.

    4. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  6. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. A01HP1Z

      Remove the grommet.

    2. Connect the cable to the negative (-) battery terminal.

    3. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. Disconnect the power window regulator master switch assembly.

    6. A01HN2F

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door glass to fall.

    7. A01HOINE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  7. REMOVE FRONT DOOR GLASS RUN


    1. A01HPZ2

      Remove the front door glass run.

  8. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY


    1. A01HMZ2E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door belt moulding assembly.

    2. A01HMBPE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the front door belt moulding assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  9. REMOVE FRONT DOOR CHECK ASSEMBLY


    1. A01HNGK

      Remove the 3 bolts and front door check assembly.

  10. REMOVE FRONT DOOR WEATHERSTRIP


    1. A01HP9A

      Using a clip remover, disengage the 19 clips and remove the front door weatherstrip.

  11. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING

    Tech Tips

    When removing the front door rear window frame moulding, heat the vehicle body and front door rear window frame moulding using a heat light.

    Heating Temperature
    Item Temperature
    Vehicle Body 40 to 60°C (104 to 140°F)
    Moulding 20 to 30°C (68 to 86°F)

    Note

    Do not heat the vehicle body or moulding excessively.


    1. Using a heat light, heat the front door rear window frame moulding.

    2. A01HNR1E01
      Text in Illustration
      *1 Double-sided Tape
      *2 Caulking Sponge

      Using a moulding remover, disengage the clip and remove the front door rear window frame moulding.

  12. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING


    1. Insert a 4.0 mm (0.157 in.) drill bit into a drill.

    2. A01HMWLE01

      Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

      Area Dimension
      A 5.0 mm

      Note

      Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against the rivets to drill off the rivet flanges, and remove the 7 rivets.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

      • Be careful of the drilled rivets, as they may be hot.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

    5. Disengage the claw and guide, and remove the front door upper window frame moulding from the door frame.