LIGHTING SYSTEM Headlight Dimmer Switch Circuit

DESCRIPTION

The main body ECU (multiplex network body ECU) receives the following switch information:


WIRING DIAGRAM

A01HOHQE08

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE USING TECHSTREAM


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the display on the Techstream.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Dimmer SW Dimmer switch high position signal/ON or OFF

      ON: Dimmer switch in high or high flash position

      OFF: Dimmer switch in low position

      		 -
      Passing Light SW Dimmer switch high flash position (pass) signal/ON or OFF

      ON: Dimmer switch in high flash position

      OFF: Dimmer switch not in high flash position

      		 -
      Front Fog Light SW Front fog light switch signal/ON or OFF

      ON: Front fog light switch on

      OFF: Front fog light switch off

      		 -
      Auto Light SW Light control switch AUTO position signal/ON or OFF

      ON: Light control switch in AUTO position

      OFF: Light control switch not in AUTO position

      		 -
      Head Light SW (Head) Light control switch head position signal/ON or OFF

      ON: Light control switch in head position

      OFF: Light control switch not in head position

      		 -
      Head Light SW (Tail) Light control switch tail position signal/ON or OFF

      ON: Light control switch in tail or head position

      OFF: Light control switch in neither tail nor head position

      		 -
      OK
      Normal conditions listed above are displayed.

    NG

    INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY

    Tech Tips

    Inspect the items that did not change as a result of monitoring the Data List.


    1. A01HPV5E05
      Text in Illustration
      *a

      Component without harness connected

      (Headlight Dimmer Switch Assembly)

      Remove the headlight dimmer switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Light Control Switch (w/ DRL OFF function)
      Tester Connection Switch Condition Specified Condition
      15 (EL) - 18 (T)

      Light control switch off

      (DRL OFF position)

      		 10 kΩ or higher
      18 (T) - 20 (A)

      Light control switch off

      (DRL OFF position)

      		 10 kΩ or higher
      20 (A) - 19 (H)

      Light control switch off

      (DRL OFF position)

      		 10 kΩ or higher
      15 (EL) - 18 (T) Light control switch in tail position Below 1 Ω
      15 (EL) - 18 (T) Light control switch in head position Below 1 Ω
      18 (T) - 19 (H) Light control switch in head position Below 1 Ω
      15 (EL) - 20 (A) Light control switch in AUTO position Below 1 Ω
      Light Control Switch (w/o DRL OFF function)
      Tester Connection Switch Condition Specified Condition
      15 (EL) - 18 (T) Light control switch off 10 kΩ or higher
      18 (T) - 20 (A) Light control switch off 10 kΩ or higher
      20 (A) - 19 (H) Light control switch off 10 kΩ or higher
      15 (EL) - 18 (T) Light control switch in tail position Below 1 Ω
      15 (EL) - 18 (T) Light control switch in head position Below 1 Ω
      18 (T) - 19 (H) Light control switch in head position Below 1 Ω
      15 (EL) - 20 (A) Light control switch in AUTO position Below 1 Ω
      Dimmer Switch
      Tester Connection Switch Condition Specified Condition
      14 (HU) - 15 (EL) Dimmer switch in low position 10 kΩ or higher
      14 (HU) - 15 (EL) Dimmer switch in high position Below 1 Ω
      15 (EL) - 17 (HF) Dimmer switch in high flash position Below 1 Ω
      Front Fog Light Switch*1
      Tester Connection Switch Condition Specified Condition
      8 (LFG) - 9 (BFG) Fog light switch off 10 kΩ or higher
      8 (LFG) - 9 (BFG) Fog light switch on Below 1 Ω

      *1: w/ Front Fog Light

      OK
      Headlight dimmer switch assembly is normal.

    NG

    REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT DIMMER SWITCH ASSEMBLY)


    1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I25-9 (BFG) - I13-27 (FFOG) Always Below 1 Ω
      I25-14 (HU) - I13-5 (HU) Always Below 1 Ω
      I25-17 (HF) - I13-8 (HF) Always Below 1 Ω
      I25-18 (T) - I13-30 (TAIL) Always Below 1 Ω
      I25-19 (H) - I13-29 (HEAD) Always Below 1 Ω
      I25-20 (A) - I13-28 (A) Always Below 1 Ω
      I25-9 (BFG) - Body ground Always 10 kΩ or higher
      I25-14 (HU) - Body ground Always 10 kΩ or higher
      I25-17 (HF) - Body ground Always 10 kΩ or higher
      I25-18 (T) - Body ground Always 10 kΩ or higher
      I25-19 (H) - Body ground Always 10 kΩ or higher
      I25-20 (A) - Body ground Always 10 kΩ or higher
      I25-15 (EL) - Body ground Always Below 1 Ω
      I25-8 (LFG) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here