LUGGAGE DOOR HINGE TORSION BAR INSTALLATION

Note

After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.


  1. INSTALL LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT


    1. A01HNIK

      Install a new luggage compartment door torsion bar support as shown in the illustration.

  2. INSTALL LUGGAGE DOOR HINGE TORSION BAR RH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      w/o Rear Spoiler
      Green
      w/ Rear Spoiler
      Pink
    2. A01HOSOE01
      Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)

      Set the tip of the luggage door hinge torsion bar RH in the center installation hole. The upper and lower installation holes are used for adjustment.

    3. A01HQ2V

      Connect the luggage door hinge torsion bar RH to the left side of the vehicle body as shown in the illustration.

    4. A01HNMA

      Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support as shown in the illustration.

    5. A01HQSHE01

      Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and the right side of the vehicle body as shown in the illustration.

      SST
      09804-24010

    6. Remove the protective tape.

  3. INSTALL LUGGAGE DOOR HINGE TORSION BAR LH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      w/o Rear Spoiler
      White
      w/ Rear Spoiler
      Yellow
    2. A01HQA9E01
      Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)

      Set the tip of the luggage door hinge torsion bar LH in the center installation hole. The upper and lower installation holes are used for adjustment.

    3. A01HMSI

      Connect the luggage door hinge torsion bar LH to the right side of the vehicle body as shown in the illustration.

    4. A01HO2U

      Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support as shown in the illustration.

    5. A01HNZEE01

      Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and the left side of the vehicle body as shown in the illustration.

      SST
      09804-24010
    6. A01HQ39

      Engage the 2 claws as shown in the illustration.

    7. A01HPJGE01

      Connect the rear seatback lock assembly LH (rear seat lock control cable LH) and engage the hook in the order indicated in the illustration.

      Tech Tips

      Use the same procedure as for the LH side and RH side.

    8. Remove the protective tape.

  4. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    1. Engage the 4 claws and install the luggage compartment door hinge cover LH.

  5. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  6. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. A01HPY3E01
      Text in Illustration
      *1 Clip <A>
      *2 Clip <B>

      Install the clip <A>.

    2. Install the 2 clips <B>.

    3. Engage the fastener and install the luggage compartment inner trim cover LH.

  7. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH


    1. A01HMYEE01
      Text in Illustration
      *1 Clip <A>
      *2 Clip <B>

      Install the clip <A>.

    2. Install the 2 clips <B>.

    3. Engage the fastener and install the luggage compartment inner trim cover RH.

  8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01HOIUE01
      Text in Illustration
      *1 Pin

      Engage the 2 pins to install the 2 No. 1 luggage compartment trim hooks.

  9. INSTALL REAR FLOOR FINISH PLATE


    1. A01HN76

      Engage the 4 clips and install the rear floor finish plate.

    2. Install the 5 clips.

  10. INSTALL SPARE WHEEL COVER ASSEMBLY


    1. Install the spare wheel cover assembly.