INSTRUMENT PANEL SAFETY PAD REMOVAL


  1. PRECAUTION

    Click here

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01HNV0

      Disengage the 10 claws and remove the front door scuff plate LH.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01HPCC

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01HOQS

      Disconnect the front door opening trim weatherstrip LH.

  6. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01HO7A

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HQ0A

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  7. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01HQT0

      Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.

  8. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01HN0NE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HMK7

      Disengage the 2 clips as shown in the illustration.

    3. A01HPHE

      Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.

  9. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. A01HOBR

      Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.

    3. A01HQAD

      Disengage the 5 claws, 5 clips and 2 guides.

    4. Disconnect each connector.

    5. A01HPGZ

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  10. REMOVE COMBINATION METER ASSEMBLY


    1. A01HNYB

      Remove the 4 screws.

    2. A01HQD0

      Disengage the wire harness clamp.

    3. Disconnect the 2 connectors to remove the combination meter assembly.

  11. REMOVE FRONT PANEL GARNISH LH


    1. A01HO8I

      Disengage the 3 claws, 2 clips and 8 guides to remove the front panel garnish LH.

  12. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01HOBK

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  13. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01HQQ4

      Remove the bolt <B> and screw <C> or <D>.

    2. A01HPRH

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  14. REMOVE FRONT PANEL GARNISH RH


    1. A01HR3Y

      Disengage the 3 claws, 2 clips and 8 guides to remove the front panel garnish RH.

  15. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01HQJ0

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  16. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY


    1. Move the shift lever to N.

    2. A01HMT3

      Disengage the 4 clips.

    3. w/ Seat heater System:


      1. Disconnect the 2 connectors.

    4. Disconnect the connector and remove the rear console upper panel sub-assembly.

  17. REMOVE CONSOLE BOX CUP HOLDER


    1. A01HPNE

      Remove the console box cup holder from the rear console upper panel sub-assembly.

  18. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY


    1. A01HP1A

      Remove the 6 screws <E> and instrument panel cup holder tray.

    2. Remove the front console upper panel garnish.

  19. REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY


    1. A01HN70

      Remove the 2 screws.

    2. A01HN9Z

      Disengage the 4 clips and remove the upper console box sub-assembly as shown in the illustration.

    3. w/ Power Outlet Socket:


      1. A01HQC0

        Disengage the clamp.

      2. Disconnect the connector to remove the upper console box sub-assembly.

  20. REMOVE NO. 4 CONSOLE BOX DUCT (w/ Rear Register Duct)


    1. A01HOX1

      Disengage the claw and remove the No. 4 console box duct.

  21. REMOVE CONSOLE BOX CARPET


    1. A01HQFE

      Remove the console box carpet.

  22. REMOVE REAR CONSOLE BOX ASSEMBLY


    1. A01HQEN

      Remove the 2 bolts and 2 screws.

    2. A01HP62

      Pull the rear console box assembly in the direction indicated by the arrow to disengage the 4 guides and remove the rear console box assembly.

  23. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01HN72

      Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

    2. A01HQ31

      Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

    3. A01HPK9

      Disengage the 3 claws and 2 clips as shown in the illustration.

    4. A01HQ1I

      Disengage the clamp.

    5. Disconnect the connector to remove the center instrument cluster finish panel assembly.

  24. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01HQDQ

      Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 6 clips to remove the No. 2 instrument panel register assembly.

  25. REMOVE BOX BOTTOM MAT


    1. A01HMY5

      Remove the box bottom mat.

  26. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01HOHW

      Remove the 2 screws <C> or <D>.

    2. A01HNXD

      Disengage the 4 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  27. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type)


    1. A01HMVKE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HOOU

      Remove the 4 bolts.

    3. A01HMQQ

      Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

  28. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type)


    1. A01HNZOE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HP6V

      Remove the 4 bolts.

    3. A01HORE

      Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

      Tech Tips

      w/ Navigation System:

      Do not disconnect the extension module connector.

  29. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type)


    1. A01HQWME01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HMNO

      Remove the 4 bolts.

    3. A01HP3J

      Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

    4. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.

  30. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY


    1. A01HN34

      Disengage the 8 clips as shown in the illustration.

    2. Disconnect the connector to remove the No. 1 speaker opening cover assembly.

  31. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)


    1. A01HPOU

      Remove the 2 screws.

    2. A01HPQY

      Lift the front No. 3 speaker assembly and disconnect the connector to remove the speaker.

      Note

      Do not touch the speaker cone.

  32. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  33. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  34. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01HO23

      Disconnect the front door opening trim weatherstrip RH.

  35. REMOVE INSTRUMENT SIDE PANEL RH


    1. A01HOT8

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HP2C

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  36. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01HMT9

      Disengage the 4 claws.

    2. Disengage the 2 guides to remove the No. 2 instrument panel under cover sub-assembly.

  37. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01HNRV

      Remove the 3 bolts.

    4. A01HNQT

      Disengage the 3 claws to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When removing the lower No. 2 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. A01HN9PE01
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Airbag Connector Lock

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  38. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01HOBP

      Remove the 2 screws <C> or <D>.

    2. Open the lower instrument panel door.

    3. A01HR3C

      Remove the 3 screws <C> or <D>.

    4. A01HQ9V

      Disengage the 2 clips and guide.

    5. A01HOXQ

      Disengage the glove compartment light as shown in the illustration.

    6. Disconnect each connector and remove the lower instrument panel sub-assembly.

  39. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01HOEH

      Disengage the 5 clips to remove the No. 2 instrument cluster finish panel garnish as shown in the illustration.

  40. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01HQJXE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HPP1

      Disengage the 2 clips as shown in the illustration.

    3. A01HONV

      Using a moulding remover, disengage the 2 clips to remove the No. 3 instrument panel register assembly.

  41. REMOVE FRONT PILLAR GARNISH LH


    1. A01HMYTE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. A01HQLME01

      While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. A01HO62E01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  42. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01HNBOE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HNHR

      Using a moulding remover, disengage the 2 clips and 3 claws.

    3. Disengage the 2 guides to remove the No.1 instrument panel speaker panel sub-assembly.

  43. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    1. A01HMAN

      Remove the 2 screws.

    2. A01HOST

      Lift the front No. 2 speaker assembly and disconnect the connector to remove the speaker.

      Note

      Do not touch the speaker cone.

  44. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  45. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01HQ8QE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HMK3

      Using a moulding remover, disengage the 2 clips and 3 claws.

    3. Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.

  46. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  47. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01HNWS

      Disengage the 4 clips to remove the lower instrument panel finish panel assembly.

    2. w/ Smart Key System:


      1. Disconnect the connector.

  48. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A01HQ1M

      Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. A01HOYZ

      Remove the 2 screws <C> or <D>.

    3. A01HR29

      Disengage the clip and 3 guides to remove the front No. 2 console box insert as shown in the illustration.

  49. REMOVE CONSOLE BOX INSERT


    1. A01HMKE

      Remove the 2 screws <C> or <D>.

    2. A01HME7

      Disengage the clip and 3 guides to remove the console box insert as shown in the illustration.

  50. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    1. Disengage the 10 clips to remove the No.1 instrument panel garnish sub-assembly as shown in the illustration.

      A01HR4O

  51. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01HN3KE01
      Text in Illustration
      *a Slider

      Slide the slider to release the lock, and then disconnect the connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  52. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. Disconnect each connector.

      A01HOCR

    2. Disengage each clamp.

    3. Remove the 2 passenger airbag bolts <A>.

      A01HQN1E01
      Text in Illustration
      *1 Passenger Airbag Bolt <A> *2 Bolt <B>
      *3 Nut <F> or <G> *4 Clip

    4. Remove the 3 bolts <B> and nut <F> or <G>.

    5. Remove the 2 clips.

    6. Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.

      A01HPDF

      Note


      • Do not damage the instrument panel safety pad assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.