CONDENSER REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. RECOVER REFRIGERANT FROM AIR CONDITIONING SYSTEM


    1. Turn the A/C switch on.

    2. Operate the air conditioning with a set temperature of 25°C (77°F) and the blower at low for 10 minutes to circulate the refrigerant. This causes most of the compressor oil from the various components of the air conditioning system to collect in the air conditioning compressor.

    3. Turn the ignition switch off.

    4. Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE FRONT BUMPER ASSEMBLY

    Click here

  5. REMOVE BATTERY (for 2GR-FE)


    1. A01HN96

      Disconnect the positive (+) cable from the positive (+) battery terminal.

    2. Loosen the nut and remove the bolt.

    3. Remove the battery and battery tray.

  6. REMOVE INLET AIR CLEANER ASSEMBLY (for 2AR-FE)


    1. A01HN8W

      Remove the 2 bolts and inlet air cleaner assembly.

  7. REMOVE INLET NO. 2 AIR CLEANER (for 2GR-FE)


    1. A01HPAY

      Disconnect the 2 wire harness clamps and vacuum hose clamp.

    2. Remove the 2 bolts and inlet No. 2 air cleaner.

  8. REMOVE INLET NO. 1 AIR CLEANER (for 2GR-FE)


    1. A01HNDX

      Disengage the pin and remove the inlet No. 1 air cleaner.

  9. REMOVE RADIATOR RESERVE TANK ASSEMBLY (for 2AR-FE)


    1. A01HO5F

      Disconnect the radiator reserve tank hose.

    2. Remove the 2 bolts and radiator reserve tank assembly.

  10. REMOVE RADIATOR RESERVE TANK ASSEMBLY (for 2GR-FE)


    1. A01HQU5

      Disconnect the radiator reserve tank hose.

    2. Remove the 2 bolts and radiator reserve tank assembly.

  11. REMOVE HOOD LOCK ASSEMBLY


    1. w/ Engine Hood Courtesy Switch:


      1. A01HNQQ

        Disconnect the connector.

    2. A01HOWK

      Remove the 3 bolts.

    3. A01HNX9

      Disconnect the hood lock control cable assembly and remove the hood lock assembly.

  12. REMOVE UPPER RADIATOR SUPPORT (for 2AR-FE)


    1. A01HOUT

      Disconnect the 2 connectors.

    2. A01HNOU

      Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.

    3. Remove the 2 radiator support cushions.

  13. REMOVE UPPER RADIATOR SUPPORT (for 2GR-FE)


    1. A01HOUT

      Disconnect the 2 connectors.

    2. A01HMGC

      Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.

    3. Remove the 2 radiator support cushions from the radiator assembly.

  14. REMOVE RADIATOR SIDE DEFLECTOR LH


    1. A01HMXL

      Disengage the 3 claws and guide remove the radiator side deflector LH.

  15. REMOVE RADIATOR SIDE DEFLECTOR RH


    1. A01HN3S

      Disengage the 3 claws and guide remove the radiator side deflector RH.

  16. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE


    1. A01HQF5

      Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the condenser.

    2. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  17. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY


    1. A01HNKO

      Remove the bolt and disconnect the air conditioning tube and accessory assembly from the condenser.

    2. Remove the O-ring from the air conditioning tube and accessory assembly.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  18. REMOVE COOLER CONDENSER ASSEMBLY


    1. A01HP19

      Remove the 4 bolts.

    2. A01HNP9

      Disengage the 2 guides and remove the cooler condenser assembly as shown in the illustration.