SEAT BELT WARNING SYSTEM Front Passenger Side Seat Belt Warning Light Malfunction

DESCRIPTION

When the ignition switch is ON, the occupant detection ECU sends a signal to the airbag sensor assembly to indicate the state of the front seat inner belt assembly RH and also whether the front passenger seat is occupied. The airbag sensor assembly sends those signals to the combination meter assembly via CAN communication. The combination meter assembly illuminates, blinks or turns off the seat belt warning light on the combination meter assembly in accordance with these signals.

Tech Tips

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.

WIRING DIAGRAM

A01HONYE06

INSPECTION PROCEDURE

Note

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure Click here.

PROCEDURE


  1. CHECK DTC OUTPUT (OCCUPANT CLASSIFICATION SYSTEM)


    1. Clear DTCs Click here.

    2. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO OCCUPANT CLASSIFICATION SYSTEM Click here

    A

  2. CHECK DTC OUTPUT (AIRBAG SYSTEM)


    1. Clear DTCs Click here.

    2. Recheck for DTCs Click here.

      Result
      Result Proceed to
      DTC is not output A
      DTC is output B

    B

    GO TO AIRBAG SYSTEM Click here

    A

  3. READ VALUE USING TECHSTREAM


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / Occupant Detection / Data List.

    5. Read the Data List according to the display on the Techstream.

      Occupant Detection (Occupant Detection ECU)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Passenger Buckle SW Front passenger buckle switch/Set, Unset or NG

      Set: Seat belt fastened

      Unset: Seat belt not fastened

      NG: Data is not determined

      		 -
      Result
      Result Proceed to
      Unset or Set is displayed on the Techstream screen according to the front passenger seat belt condition A

      Unset or Set is not displayed normally on the Techstream screen according to the front passenger seat belt condition

      (for Manual Seat)

      		 B

      Unset or Set is not displayed normally on the Techstream screen according to the front passenger seat belt condition

      (for Power Seat)

      		 C
      NG is displayed on the Techstream screen D

    B

    REPLACE FRONT SEAT INNER BELT ASSEMBLY RH Click here

    C

    REPLACE FRONT SEAT INNER BELT ASSEMBLY RH Click here

    D

    REPLACE OCCUPANT DETECTION ECU Click here

    A

  4. READ VALUE USING TECHSTREAM


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Enter the following menus: Body Electrical / SRS Airbag / Data List.

    5. Read the Data List according to the display on the Techstream.

      SRS Airbag (Airbag Sensor Assembly)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Right side Buckle SW RH buckle switch/Unset, Set or NG

      Unset: Seat belt is not fastened

      Set: Seat belt is fastened

      NG: Data is not determined

      		 -
      Result
      Result Proceed to
      Unset or Set is displayed on the Techstream screen according to the front passenger seat belt condition A

      • Unset or Set is not displayed normally on the Techstream screen according to the front passenger seat belt condition

      • NG is displayed on the Techstream screen

      		 B

    B

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    A

    USE SIMULATION METHOD TO CHECK Click here