AIRBAG SYSTEM, Diagnostic DTC:B1650/32

DTC Code DTC Name
B1650/32 Occupant Classification System Malfunction

DESCRIPTION

The occupant classification system circuit consists of the airbag sensor assembly and occupant classification system.

If the airbag sensor assembly receives signals from the occupant detection ECU, it determines whether the front passenger airbag and front passenger side knee airbag should be operated.

DTC B1650/32 is stored when a malfunction is detected in the occupant classification system circuit.

DTC No. DTC Detection Condition Trouble Area
B1650/32

  • The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the occupant classification system circuit.

  • Occupant classification system malfunction

  • Airbag sensor assembly malfunction

  • No. 2 floor wire

  • Front seat wire RH

  • Occupant classification system

  • Airbag sensor assembly

WIRING DIAGRAM

A01HNMJE05

INSPECTION PROCEDURE

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

PROCEDURE


  1. CHECK DTC (OCCUPANT DETECTION ECU)


    1. Check for DTCs of the occupant detection ECU Click here.

      OK
      DTC is not output.

    NG

    GO TO OCCUPANT CLASSIFICATION SYSTEM Click here

    OK

  2. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and occupant detection ECU. Also check that the connectors that link the No. 2 floor wire and front seat wire RH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and occupant detection ECU. Also disconnect the connectors that link the No. 2 floor wire and front seat wire RH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  3. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (OPEN)


    1. A01HOEGE02
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Occupant Detection ECU)

      Connect the connectors that link the No. 2 floor wire and front seat wire RH.

    2. Using a service wire, connect terminals 16 (FSR+) and 24 (FSR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      d11-7 (FSR+) - d11-4 (FSR-) Always Below 1 Ω

    NG

    CHECK NO. 2 FLOOR WIRE (OPEN) Click here

    OK

  4. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT)


    1. A01HO0EE03
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *a

      Front view of wire harness connector

      (to Occupant Detection ECU)

      Disconnect the service wire from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      d11-7 (FSR+) - d11-4 (FSR-) Always 1 MΩ or higher

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT) Click here

    OK

  5. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO B+)


    1. A01HO0EE03
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *a

      Front view of wire harness connector

      (to Occupant Detection ECU)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      d11-7 (FSR+) - Body ground Ignition switch ON Below 1 V
      d11-4 (FSR-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


    NG

    CHECK NO. 2 FLOOR WIRE (SHORT TO B+) Click here

    OK

  6. CHECK OCCUPANT CLASSIFICATION SYSTEM CIRCUIT (SHORT TO GROUND)


    1. A01HO0EE03
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *a

      Front view of wire harness connector

      (to Occupant Detection ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      d11-7 (FSR+) - Body ground Always 1 MΩ or higher
      d11-4 (FSR-) - Body ground Always 1 MΩ or higher

    NG

    CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND) Click here

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  7. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01HPZ9E02
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *3 Front Seat Wire RH
      *4 No. 2 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Front Seat Wire RH)

      Disconnect the front seat wire RH from the No. 2 floor wire.

      Tech Tips

      The service wire has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Od2-1 (FSR+) - Od2-5 (FSR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

    REPLACE FRONT SEAT WIRE RH

  8. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A01HOKHE02
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *3 Front Seat Wire RH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Seat Wire RH)

      Disconnect the front seat wire RH from the No. 2 floor wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Od2-1 (FSR+) - Od2-5 (FSR-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

    REPLACE FRONT SEAT WIRE RH

  9. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01HOKHE02
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *3 Front Seat Wire RH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Seat Wire RH)

      Disconnect the front seat wire RH from the No. 2 floor wire.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      Od2-1 (FSR+) - Body ground Ignition switch ON Below 1 V
      Od2-5 (FSR-) - Body ground Ignition switch ON Below 1 V

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

    REPLACE FRONT SEAT WIRE RH

  10. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01HOKHE02
      Text in Illustration
      *1 Occupant Detection ECU
      *2 Airbag Sensor Assembly
      *3 Front Seat Wire RH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Front Seat Wire RH)

      Disconnect the front seat wire RH from the No. 2 floor wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Od2-1 (FSR+) - Body ground Always 1 MΩ or higher
      Od2-5 (FSR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

    REPLACE FRONT SEAT WIRE RH