FRONT DOOR LOCK INSTALLATION

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.


  1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A01HQEZ

      Install the front door inside locking cable assembly.

    2. A01HMA8

      Engage the 3 claws.

  2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A01HOSY

      Install the front door lock remote control cable assembly.

  3. INSTALL FRONT DOOR LOCK WITH MOTOR ASSEMBLY

    Note


    • When reusing the removed front door lock with motor assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock with motor assembly.


    1. Apply MP grease to the sliding parts of the front door lock with motor assembly.

    2. When reusing the front door lock with motor assembly.


      1. Install a new door lock wiring harness seal to the front door lock with motor assembly.

    3. A01HQZJE01
      Text in Illustration
      *1 Front Door Lock Open Rod

      Insert the front door lock open rod to the front door lock with motor assembly.

    4. Make sure that the front door lock open rod is securely connected to the front door lock with motor assembly.

    5. Using a T30 "TORX" socket wrench, install the front door lock with motor assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (w/ Lock Cylinder)


    1. A01HQJY

      Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }
    2. A01HR2Q

      Install the hole plug.

  5. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. A01HOVG

      Engage the guide as shown in the illustration.

    2. Install the front door rear lower frame sub-assembly with the 2 bolts.

  6. INSTALL FRONT DOOR GLASS RUN


    1. A01HPZ2

      Install the front door glass run.

  7. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. Disconnect the power window regulator master switch assembly.

    5. A01HQ44E01

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.

    6. A01HN2F

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    7. A01HP1Z

      Install the grommet.

  8. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the front door panel.

    2. A01HO5IE01
      Text in Illustration
      *1 Reference Point

      Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.

    3. Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. Engage the 5 clamps.

    5. Install the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    6. Connect each connector.

  9. INSTALL DOOR SIDE AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01HQ1GE01
      Text in Illustration
      *a Incorrect *b Correct

    4. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Make sure that the pin (stopper) is securely inserted into the body hole.

      • Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. Connect the connector to the door side airbag sensor.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.


      1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        A01HPZXE12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connection is Completed - -

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

    6. Check that there is no looseness in the installation parts of the door side airbag sensor.

  10. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A01HN52

      Install the front door inner glass weatherstrip.

  11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01HNLZE01
      Text in Illustration
      *1 Front Door Inside Locking Cable Assembly
      *2 Front Door Lock Remote Control Cable Assembly

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

    2. A01HNHDE01
      Text in Illustration
      *1 Reference Boss

      Engage the front door trim board sub-assembly with the 4 claws and reference boss as shown in the illustration.

    3. A01HMKR

      Engage the 10 clips and install to front door trim board sub-assembly.

    4. Install the 3 screws.

    5. If protective tape has been applied, remove it.

  12. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01HPSME01
      Text in Illustration
      *A for LH Side
      *B for RH Side

      Engage the claw to install the courtesy light assembly.

  13. INSTALL FRONT ARMREST ASSEMBLY


    1. A01HP7E

      Engage the 2 guides, 3 clips and 7 claws, and install the front armrest assembly.

  14. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. Connect each connector.

    2. A01HNDT

      Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator master switch assembly with front door armrest base panel.

  15. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect each connector.

    2. A01HOGB

      Engage the 4 guides, 2 clips and 5 claws, and install the power window regulator switch assembly with front door armrest base panel.

  16. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01HNP7

      Engage the 3 clips to install the front door lower frame bracket garnish.

  17. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01HPRN

      Engage the 3 claws to install the front door inside handle bezel plug.

  18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  19. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)

    Click here

  20. CHECK POWER WINDOW CONTROL SYSTEM

    Click here

  21. INSPECT SRS WARNING LIGHT

    Click here