CAN COMMUNICATION SYSTEM Check CAN Bus Lines for Short Circuit

DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.

  • Short in CAN main bus line

  • Short in CAN branch line

  • Network gateway ECU*1

  • ECM

  • Main body ECU (Multiplex network body ECU)

  • Combination meter assembly

  • Brake actuator assembly (Skid control ECU)

  • Steering sensor

  • Clearance warning ECU assembly*2

  • Air conditioning amplifier assembly

  • Smart key ECU assembly (Certification ECU)*3

  • Navigation receiver assembly*4

  • Navigation ECU sub-assembly*5

  • Radio and display receiver assembly*6

  • Power steering ECU with motor assembly*7

  • Power steering ECU assembly*8*9

  • Airbag sensor assembly

  • CAN No. 1 junction connector

  • CAN No. 2 junction connector

WIRING DIAGRAM

A01HODKE02
A01HNIQE01

INSPECTION PROCEDURE

Note


  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output Click here.

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

  • DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 31 seconds and then drive the vehicle at a speed of 20 km/h (12 mph) or more for 5 minutes or more. Check that the warning light remains off after turning off following the initial light check.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed Click here.

Tech Tips


  • Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

  • Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.

PROCEDURE


  1. CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. A01HNJNE03
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN No. 1 Junction Connector)
      *b to DLC3

      Disconnect the DLC3 branch line connector (I96) from the CAN No. 1 junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    3. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

    OK

  2. CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE)


    1. Reconnect the DLC3 branch line connector (I96) to the CAN No. 1 junction connector.

    2. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.

    3. While observing the resistance value shown on the tester, disconnect connectors I95, I97, I100, I102, I103, I105, I106, I107, I108 and I111 from the CAN No. 1 junction connector or CAN No. 2 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

      Tech Tips

      Disconnect the branch line connectors other than those of the DLC3.

      A01HPJAE02
      Text in Illustration
      *A w/ Intuitive Parking Assist System *B w/ Smart Key System
      *C w/ Blind Spot Monitor System *D for Navigation Receiver Type
      *E for Radio and Display Type w/ Intuitive Parking Assist System *F for Radio and Display Type w/o Intuitive Parking Assist System
      *G for 2AR w/ Wireless Door Lock System *H for 2AR w/o Wireless Door Lock System
      *I for 2GR-FE - -
      *1 Clearance Warning ECU Assembly *2 Air Conditioning Amplifier Assembly
      *3 ECM *4 Brake Actuator Assembly (Skid Control ECU)
      *5 Smart Key ECU Assembly (Certification ECU) *6 Network Gateway ECU
      *7 Navigation Receiver Assembly *8 Navigation ECU Sub-assembly
      *9 Radio and Display Receiver Assembly *10 Combination Meter Assembly
      *11 Power Steering ECU with Motor Assembly *12 Power Steering ECU Assembly
      *13 DLC3 *14 Airbag Sensor Assembly
      *15 Steering Sensor *16 Main Body ECU (Multiplex Network Body ECU)
      *17 CAN No. 2 Junction Connector *18 CAN No. 1 Junction Connector
      A01HQPZE01
      Text in Illustration
      *a

      Component without harness connected

      (CAN No. 1 Junction Connector)

      		 - -
      Wiring Color
      CAN No. 1 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
      Main body ECU (Multiplex network body ECU) I95 P W
      Steering sensor I97 V W
      Airbag sensor assembly I103 Y W
      DLC3 I96 L W

      • Power steering ECU with motor assembly*1

      • Power steering ECU assembly*2*3

      		 I100 G W
      Combination meter assembly I94 R W
      CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I93 B W

      • *1: for 2AR w/ wireless door lock system

      • *2: for 2AR w/o wireless door lock system

      • *3: for 2GR-FE

      A01HMSME02
      Text in Illustration
      *a

      Component without harness connected

      (CAN No. 2 Junction Connector)

      		 - -
      Wiring Color
      CAN No. 2 Junction Connector Side Code Color (CANH Side) Color (CANL Side)
      CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector) I101 B W

      • Navigation receiver assembly*1

      • Navigation ECU sub-assembly*2

      • Radio and display receiver assembly*3

      		 I107 R W
      Network gateway ECU*4 I108 G W
      Smart key ECU assembly (Certification ECU)*5 I106 L W
      Brake actuator assembly (Skid control ECU) I105 Y W
      Air conditioning amplifier assembly I102 V W
      ECM I104 P W
      Clearance warning ECU assembly*6 I111 BE W

      • *1: for Navigation receiver type

      • *2: for Radio and display type w/ intuitive parking assist system

      • *3: for Radio and display type w/o intuitive parking assist system

      • *4: w/ Blind spot monitor system

      • *5: w/ Smart key system

      • *6: w/ Intuitive parking assist system

      Note

      Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.

      Result
      Symptom Proceed to
      The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of the branch lines.) A
      The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.) B

    4. When there is a short in one or more of the branch lines:


      1. Reconnect all of the connectors to the CAN J/C, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

        Tech Tips


        • Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.

        • Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


    B

    CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR) Click here

    A

  3. CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN BUS LINE)


    1. A01HQUFE04
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN No. 1 Junction Connector)
      *b to Combination Meter Assembly

      Disconnect the combination meter assembly main bus line connector (I94) from the CAN No. 1 junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    2. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Result
      Symptom Proceed to
      The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.) A
      The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.) B

    B

    CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY) Click here

    A

  4. CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN BUS LINE)


    1. A01HMT6E03
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN No. 2 Junction Connector)
      *b to ECM

      Disconnect the ECM main bus line connector (I104) from the CAN No. 2 junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    2. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

      Tech Tips

      Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.

      Result
      Symptom Proceed to
      The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.) A
      The resistance becomes 1 MΩ or more when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.) B

    B

    CHECK FOR SHORT IN CAN BUS LINES (ECM) Click here

    A

  5. CHECK CAN NO. 1 JUNCTION CONNECTOR


    1. A01HPDXE04
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN No. 1 Junction Connector)
      *b to CAN No. 2 Junction Connector

      Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    2. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

    NG

    REPLACE CAN NO. 1 JUNCTION CONNECTOR

    OK

  6. CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)


    1. Reconnect the CAN main bus line connector (I93) to the CAN No. 1 junction connector.

    2. A01HPEYE08
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to CAN No. 2 Junction Connector)
      *b to CAN No. 1 Junction Connector

      Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.

      Note


      • Before disconnecting the connector, make a note of where it is connected.

      • Reconnect the connector to its original position.

    3. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher

    NG

    REPAIR OR REPLACE CAN BUS MAIN LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)

    OK

    REPLACE CAN NO. 2 JUNCTION CONNECTOR

  7. CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)


    1. Reconnect the connector for the short-circuited branch line to the CAN J/C (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).

    2. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the short-circuited branch line is connected Click here.

    3. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

      Tech Tips

      If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).


    NG

    REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR

    OK

    REPLACE CORRESPONDING ECU OR SENSOR

  8. CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY)


    1. Reconnect the combination meter assembly main bus line connector (I94) to the CAN No. 1 junction connector.

    2. Disconnect the combination meter assembly connector (I18).

    3. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

      Tech Tips

      If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.


    NG

    REPAIR OR REPLACE CAN BUS MAIN LINES (COMBINATION METER ASSEMBLY MAIN BUS LINES)

    OK

    REPLACE COMBINATION METER ASSEMBLY Click here

  9. CHECK FOR SHORT IN CAN BUS LINES (ECM)


    1. Reconnect the ECM main bus line connector (I104) to the CAN No. 2 junction connector.

    2. Disconnect the ECM connector (A25).

    3. A01HOVAE53
      Text in Illustration
      *1 DLC3

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher
      Result
      Result Proceed to
      OK (for 2GR-FE) A
      OK (for 2AR-FE) B
      NG C

      Tech Tips


      • Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.

      • If the resistance changes to 1 MΩ or more when the connector is disconnected, there may be a short in the ECM.


    B

    REPLACE ECM Click here

    C

    REPAIR OR REPLACE CAN BUS MAIN LINES (ECM MAIN BUS LINES)

    A

    REPLACE ECM Click here