RADIO RECEIVER REMOVAL


  1. PRECAUTION (for Radio and Display Type with Intuitive Parking Assist System)

    Note


    • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

    • A Hard Disk Drive (HDD) is built into the radio and display receiver assembly to store multi-media data, and is used for the audio and visual system. Therefore, care must be taken when handling the radio and display receiver assembly.

    • When removing the hard disc drive, eliminate static electricity by touching the vehicle body to prevent components from being damaged.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Radio and Display Type with Intuitive Parking Assist System)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  4. REMOVE BOX BOTTOM MAT


    1. A01HMY5

      Remove the box bottom mat.

  5. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01HOHW

      Remove the 2 screws <C> or <D>.

    2. A01HNXD

      Disengage the 4 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  6. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01HN72

      Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

    2. A01HQ31

      Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.

    3. A01HPK9

      Disengage the 3 claws and 2 clips as shown in the illustration.

    4. A01HQ1I

      Disengage the clamp.

    5. Disconnect the connector to remove the center instrument cluster finish panel assembly.

  7. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01HQDQ

      Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 6 clips to remove the No. 2 instrument panel register assembly.

  8. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type)


    1. A01HMVKE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HOOU

      Remove the 4 bolts.

    3. A01HMQQ

      Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

  9. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio and Display Type)


    1. A01HNZOE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HP6V

      Remove the 4 bolts.

    3. A01HORE

      Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 8 clips.

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

      Tech Tips

      w/ Navigation System:

      Do not disconnect the extension module connector.

  10. REMOVE NO. 1 RADIO BRACKET (for Radio Receiver Type)


    1. A01HQTA

      Remove the 5 screws and No. 1 radio bracket.

  11. REMOVE NO. 2 RADIO BRACKET (for Radio Receiver Type)


    1. A01HN7H

      Remove the 5 screws and No. 2 radio bracket.

  12. REMOVE NO. 1 RADIO BRACKET (for Radio and Display Type)


    1. w/o Navigation System:


      1. A01HPE5

        Remove the 5 screws and No. 1 radio bracket.

    2. w/ Navigation System:


      1. A01HNXM

        Remove the 7 screws and No. 1 radio bracket.

  13. REMOVE NO. 2 RADIO BRACKET (for Radio and Display Type)


    1. w/o Navigation System:


      1. A01HN1I

        Remove the 5 screws and No. 2 radio bracket.

    2. w/ Navigation System:


      1. A01HR4K

        Remove the 7 screws and No. 2 radio bracket.

  14. REMOVE NO. 1 RADIO RECEIVER BRACKET (for Radio and Display Type with Intuitive Parking Assist System)


    1. A01HQ3C

      Remove the 5 screws and No. 1 radio receiver bracket.

  15. REMOVE NO. 2 RADIO RECEIVER BRACKET (for Radio and Display Type with Intuitive Parking Assist System)


    1. A01HNDR

      Remove the 5 screws and No. 2 radio receiver bracket.

  16. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    1. A01HO4M

      Disengage the 4 clips and guide, and remove the air conditioning control assembly as shown in the illustration.

  17. REMOVE EXTENSION MODULE (for Radio and Display Type)

    w/ Navigation System: Click here

  18. REMOVE RADIO RECEIVER ASSEMBLY (for Radio Receiver Type)

  19. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)

  20. REMOVE HARD DISK DRIVE (for Radio and Display Type with Intuitive Parking Assist System)


    1. A01HMMG

      Remove the 2 screws.

    2. Disengage the 2 guides to remove the cover.

    3. A01HQJ7

      Pull out the hard disk drive from the navigation receiver assembly or radio and display receiver assembly in the direction shown by the arrow in the illustration to remove it.

  21. REMOVE NAVIGATION ECU SUB-ASSEMBLY (for Radio and Display Type with Intuitive Parking Assist System)